بایگانی برچسب: abaqus concrete damage modeling

In this tutorial, the Simulation of concrete-encased CFST box stub columns under axial compression in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The steel pipes are modeled as three-dimensional solid part also,  and the steel bar and strips are modeled as the wire ...

In this tutorial, the Simulation RC beam column joint reinforced with steel plates and rods under vertical load in abaqus  has been investigated. The concrete beam-column is modeled as a three-dimensional solid part. The steel bar and strip are modeled as three-dimensional wire part. The steel plates and rods are ...

In this tutorial, the Simulation five point bending of a composite concrete beam(NSC+UHPFRC) in Abaqus has been done. The normal strength concrete beam as a cover is modeled as a three-dimensional solid part. The Ultra-High-Performace-Fiber-Reinforce-Concrete core is modeled as the a three-dimensional solid part. The steel bars and strips are ...

In this tutorial, the Simulation dynamic compression test of a RC column with UHPFRC core in Abaqus has been done, The concrete column is modeled as a three-dimensional solid part. The steel bar and strip are modeeld as three-dimensional wire paer. The Ultra-High-Performance-Fiber-Reinforce Concrete is modeled as a three-dimensional solid ...

In this tutorial, the Simulation dynamic four point bending test of a Gravity beam in Abaqus has been investigated. Gravity Beams, a term coined in this investigation, are those beams in which gravity is used to design the topology of beam form conjointly with the novel manufacturing strategy Fabric Formwork. ...

In this tutorial, the Numerical Investigation of Rigid Impact on Steel Wire Reinforced Foam Core/Composite Skin Sandwich Panel in Abaqus software has been investigated. The rigid projectile is modeled as the three-dimensional shell part. The steel reinforcements are modeled as wire part. The glass-epoxy part is modeled as a three-dimensional ...

In this tutorial, Simulation low energy impact of a rigid hammer on the wood-cement-concrete panel in Abaqus has been investigated. The panel contians three layers, top layer is wood-cement part as a soild model, the second layer is normal strenght concrete as a solid part, and third layer is wood-cement ...

In this tutorial the Simulation rocket impact and explosion over a concrete panel in Abaqus has been investigated. The concrete panel is modeled as a three-dimensional solid part. The rocket is modeled as a three-dimensional shell part, and the TNT is modeeld as a solid part. You can see a ...

در این ویدئوی آموزشی به شبیه سازی برخورد و انفجار راکت به روش اس پی اچ و بررسی آسیب بتن در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه بتن به صورت سالید و سه بعدی، هندسه راکت به صورت شل و سه بعدی و در نهایت پارت ماده منفجره ...

In this tutorial, the Simulation air blast load over a composite panel(Aluminum+bamboo fiber) in Abaqus has been investigated. Because of the symmetry circumstance, one quarter of the geometries are modeled. The aluminum plates are modeled as three-dimensional solid part. The bamboo plate as a core of the composite panel is ...

In this tutorial, the Simulation four point bending test of a foamed concrete beam reinforced with steel bars and bamboo fiber in Abaqus has been investigated. The foamed concrete part is modeled as a three-dimensional solid part. The bamboo composite is modeled as a three-dimensional shell part with some layers. ...

In this tutorial, the Simulation air blast explosion over a steel-UHPC-steel sandwich composite beam stud connectors in Abaqus has been studied. The two steel plates with studs are modeled as three-dimensional solid part. The UHPC is modeled as a three-dimensional solid part as a core of the sandwich beam. You ...

In this tutorial, the Simulation high-velocity impact on the Aluminum-Bamboo sandwich panel in Abaqus has been done. The aluminum plate is modeled as a three-dimensional solid part. The bamboo plate is modeled as a shell part with thirty two layers with different fiber angle. The projectile is modeled as a ...

In this tutorial, the Simulation dynamic bending test of SCS sandwich beams with UHPFRC in Abaqus has been investigated. The upper and bottom steel plates with studs are modeled as three-dimensional solid part. The middle UHPFRC is modeled as a three-dimensional solid part. You can see a figure of the ...

در این ویدئوی آموزشی به شبیه سازی خمش دینامیکی تیر مرکب شامل ورق گلمیخدار به همراه بتن الیافی در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل دو ورق رویی و زیرین به همراه تعدادی گلمیخ در سطح آنها می باشد، که به صورت سالید و سه بعدی طراحی شده اند. ...

In this tutorial, the Simulation cyclic loading of a steel beam embedded in a concrete block in Abaqus has been done. The steel beam (or column) is modeled as a three-dimensional shell part. The concrete block is modeled as a three-dimensional solid part. The half of the steel beam is ...

در این ویدئوی آموزشی به شبیه سازی بارگذاری سیکلی تیر فولادی تا نیمه مدفون در بتن در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل یک تیر فولادی به صورت شل(یا سالید)، و پایه بتنی به صورت سالید می باشد. تیر تا نیمه در بتن ...

In this tutorial, the Numerical simulation of interlocking blocks under compression in Abaqus has been done. The blocks are modeled as three dimensional solid parts with interlocking surfaces. You can see a figure of the assembled parts below Masonry structure is one of the most predominant structures throughout the world ...

در این ویدئوی آموزشی به شبیه سازی تست فشار آجرهای به هم پیوسته(Interlocking) با تعریف تماس چسبنده در آباکوس پرداخته ایم. ستون آجرهای در هم تنیده به صورت سالید و سه بعدی طراحی شده اند، که تعداد آنها و نحوه در هم تنیدگی می تواند متفاوت باشد. ملات بین آجرها ...

In this tutorial, the Simulation sequential CEL explosion in the depth of soil over the RC slab in Abaqus has been investigated. The concrete slab is modeled as three-dimensional solid part, the steel reinforcement is modeled as wire part. The Soil, and TNT are modeled as three-dimensional solid parts. The ...

In this tutorial, the Simulation UHPFRC beam with initial void reinforced with CFRP rod and Expoxy under dynamic bending has been investigated. The concrete beam, CFRP rod, epoxy glu are modeled as three-dimensional solid parts. Two rigid body as a hydraulic jacks also are modeled. You can see a figure ...

در این ویدئوی آموزشی به شبیه سازی خمش دینامیکی تیر بتنی فوق توانمند الیافی با حفره اولیه تقویت شده با چسب و میلگرد CFRP در آباکوس پرداخته ایم. تیر بتنی به صورت تو پر و سه بعدی، میلگرد کامپوزیتی به صورت تو پر و سه بعدی، چسب به صورت تو ...

In this tutorial, the Simulation air blast explosion over the rebberized concrete column reinforced with green composite in Abaqus has been done. The rubberized concrete column is modeled as a three-dimensional solid part. The green composite with some layers is modeled as a three-dimensional shell part. The steel reinforcements are ...

In this tutorial, the Simulation dynamic bending test of a rubberized concrete beam reinforced with green composite  in abaqus has been investigated. The rubberized concrete beam is modeled as a three-diensional solid part. The green composite is modeled as a three-dimensional shell part with four layups. The steel bas and ...

In this tutorial the explosion simulation near the reinforced concrete wall with green composite-SPH method- has been investigated. The TNT part is modeled as a three-dimensional solid part. The concrete wall or slab is modeled as three-dimensional solid part, the green composite part with eight layers is modeld as three-dimensional ...

In this tutorial the Simulation low energy impact on the concrete slab with pre tensioned bars reinforced with GFRP in Abaqus has been studeid. Concrete is modeled as a three-dimensional solid part. The GFRP part is model as plannar shell part. The steel basrs are modeled as three-dimensional wire part ...

This tutorial investigates a Simulation air blast explosion test over a reinforced UHPC- Damage analysis. The Ultra-High-Performance Concrete is modeled as the three-dimensional solid part. The embedded bars and strips parts are modeled as a three-dimensional wire part. You can see a figure of the assembled parts below The UHPC ...

در این ویدئوی آموزشی به شبیه سازی انفجار در هوا روی یک ستون بتنی فوق توانمند تقویت شده با میلگرد در نرم افزار آباکوس-بررسی تخریب- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و تیر بتنی به صورت یک پارت سالید و سه بعدی، میلگردها و خاموت ها به صورت ...

In this tutorial, the Simulation of steel projectile impact to the Reinforced-Ultra-High-Performance Concrete- Damage investigation has been investigated. The Ultra-High-Performance Concrete is modeled as the three-dimensional solid part, the embedded beam parts are modeled as a three-dimensional wire part, and finally, the steel projectile is modeled as a solid part. ...

در این ویدئوی آموزشی به شبیه سازی برخورد پرتابه سرعت بالا به پنل بتنی فوق توانمند در آباکوس- بررسی تخریب- پرداخته ایم. مدلسازی شامل دال بتنی فوق توانمند به صورت سه بعدی و تغییر شکلپذیر، دو لایه میلگرد به صورت سه بعدی و سیمی، و جسم ضربه زننده فولادی به ...

In this package, the high and low-velocity impacts are investigated through 40 step-by-step tutorials for more than 20 hours. Through those 40 separated simulations, all aspects of the impact and collision are studied. Each tutorial contains cae, inp, step-by-step English video, and papers, also some of them have codes. Impact ...

In this lecture through ten step-by-step tutorials, many aspects of the crack growth like XFEMm H integral, and … in concrete, steel, dam, bone, and…are investigated. All the tutorials are explained from A to Z, each tutorial contains cae, inp, and step-by-step English video. All the tutorials in the package ...

در این پکیج آموزشی در قالب ۱۵ مثال کاربردی سعی گردیده شده است تا تمامی جوانب رشد ترک به روش های مختلف تشرریح و توضیح داده شود. در هر مثال از پکیج رشد ترک در ماده خاصی به صورت سه بعدی و یا دوبعدی در نظر گرفته شده است. مثالهای ...

در این پکیج سعی شده که با توجه به مدل های مختلف موجود در پدیده برخورد سرعت بالا و پایین، مسائلی کاربردی و متونع گنجانده شود. مثالهای از قبیل برخورد تکراری، برخورد پرتابه به پنل بتنی و فولادی، برخورد به لایه های کامپوزیتی،سرامیکی، لوله های فولادی، گسیختگی در اثر ضربه، ...

در این پکیج سعی بر این بوده که مسائل مختلفی مربوط به تحلیل های سازه ای بتن( انواع بتن) گنجانده شود. مسائلی مربوط به تیر،ستون، اتصالات، بارگذاری تکراری، برخورد تکراری،بتن فوق توانمند و الیافی، مسائل مربوط به آسیب، تیرو ستون های کامپوزیت،…در این پکیج در قالب فایل آموزشی قرار داده ...

In this tutorial, the Simulation RC beam under the repeated impact of the rigid hammer in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The steel rebar and strips are modeled as three-dimensional wire parts. The rigid hammer is modeled as a three-dimensional rigid ...

در این ویدئوی آموزشی به شبیه سازی برخورد تکراری یک جسم صلب به تیر بتنی مسلح در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و تیر بتنی به صورت سالید، میلگرد و خاموت ها به صورت وایر، و جسم صلب به صورت شل و ریجید طراحی ...

In this tutorial, the Numerical analysis of tilted angle shear connectors in steel-concrete composite systems in Abaqus has been investigated. The concrete block is modeled as a three-dimensional solid part. The steel beam and steel angle connector are modeled as three-dimensional solid parts. Two rigid bodies are used as boundary ...

در این ویدئوی آموزشی به شبیه سازی نبشی اتصال دهنده برشی در سیستم بتنی-فولادی در آباکوس- تعیین ظرفیت باربری- پرداخته ایم. مدلسازی شامل چند پارت از قبیل ستون فولادی به صورت سه بعدی و تغییر شکلپذیر، پارت بتنی به صورت سه بعدی و تغییر شکلپذیر، پارت نبشی زاویه دار به ...

In this tutorial, the Simulation compression test of the concrete column with and without steel reinforcement-Compression test- has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts and two rigid bodies as boundary zone and hydraulic jack. You can ...

در این ویدئوی آموزشی به شبیه سازی تست فشار ستون کوتاه بتنی با و بدون تقویت کننده فلزی در آباکوس-مقایسه باربری- پرادخته ایم. مدلسازی به صورت سه بعدی شامل هندسه ستون بتنی، میلگرد ها و اجسام صلب در نقش تکیه گاه و جسم وارد کننده نیرو می باشد. ستون بتنی ...

In this tutorial, the Simulation RC column retrofitted with CFRP and epoxy under compression load in Abaqus has been done. The circular concrete column is modeled as a three-dimensional solid part. The sell strips and bars are modeled as three-dimensional wire parts. The CFRP is modeled as a conventional shell ...

In this tutorial, the Seismic behavior of RC exterior wide beam-column joints in Abaqus has been simulated. The concrete beam and column are modeled as three-dimensional solid parts. The steel bars and strips are modeled as three-dimensional wire parts. You can see a figure of the assembled parts below Reinforced ...

In this tutorial, the High-velocity impact of a bullet on the RC panel- Paper validation- is investigated. The dimensions are extracted from the paper. The concrete slab is modeled as a three-dimensional solid part. The steel reinforcements are modeled as three-dimensional wire parts. The bullet is modeled as a discrete ...

In this lecture, the High and Low-velocity impact phenomenon is investigated. The lecture duration is more than ten hours and during that, twenty different models are simulated based on the research paper as a reference for the material. We define the proper material model for each part for instance in ...

In this lecture through Twenty step by step tutorial, many aspects of the concrete structure like a beam, RC beam and column, normal concrete, UHPC, and UHPFRC concrete, composite beam, and column, cyclic loading over the RC beam and column, CFDST and CFST column, ECC beam-column joint, high strength concrete ...

In this tutorial, the Simulation cyclic loading of a composite Column(UHPC + Steel box) in Abaqus has been studied. The Ultra-High-Performance Concrete column is modeled as a three-dimensional solid part. The steel box cover is modeled as a three-dimensional shell part. You can see a figure of the assembled parts ...

In this tutorial, the Simulation cyclic loading behavior of a reinforced rubberized concrete column in Abaqus has been investigated. The rubberized concrete column is modeled as a three-dimensional solid part. The steel bars and strips are modeled as three-dimensional wire part. You can see a figure of the assembled parts ...

In this tutorial, the Simulation of low energy impact on the RC beam and residual displacement investigation in Abaqus has been done. The concrete beam is modeled as a three-dimensional solid part. The steel bars and strips are modeled as three-dimensional wire parts. The hammer is modeled as a rigid ...

در این مثال آموزشی به شبیه سازی تیر بتنی مسلح تحت اثر ضربه کم انرژی در نرم افزار آباکوس-بررسی جابه جایی پسماند- در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل تیر بتنی به صورت سالید، میلگردهای طولی و خاموت ها به صورت سه بعدی ...