بایگانی برچسب: concrete

Numerical simulation of concrete-filled double skin steel tubular (CFDST) structure subjected to underwater explosion loading in Abaqus has been don in this example. The concrete column is modeled as a three-dimensional solid part. The inner and outer steel tubes are modeled as shell parts. The air, water, and TNT are ...

The Cyclic Test Simulation of Concrete-Filled Steel Column in Abaqus-Validation Analysis has been done in this tutorial. The steel box column, ribs, and stiffener plates are modeled as three-dimensional shell parts. The two concrete blocks are modeled as three-dimensional solid parts. You can see the figures of the assembled parts ...

In this tutorial, the Simulation hollow-core slab under fire conditions and four-point bending in Abaqus has been investigated. Precast/prestressed concrete hollow core (PCHC) slabs with a reduction in self-weight due to longitudinal voids, and without shear reinforcement due to the extrusion method are most susceptible to shear failure. When subjected ...

In this tutorial, the Simulation bending test of the steel-concrete composite beam in SRC structures considering bond-slip behavior in Abaqus has been investigated. The steel-concrete composite beam is modeled as a three-dimensional solid part. The steel reinforcements are modeled as the wire parts. You can see a figure of the ...

In this tutorial, the Simulation of ceramic plates as shielding for concrete blocks against projectile penetration(SPH method) has been done. The ceramic plate and Ultra-High-Performance-Concrete are modeled as three-dimensional solid parts. The bullet is modeled as a solid part. You can see a figure of the assembled parts below In ...

In this tutorial, the Simulation of the UHPC beam-column joint reinforced with steel angle and bolts in Abaqus has been investigated. The Ulta-High-Performance-Concrete beam-column joint is modeled as a three-dimensional solid part. The steel bar and strips are modeled as three-dimensional wire parts. The steel angle, plates, and bolts are ...

In this tutorial, the Simulation load bearing capacity of a composite joint between a reinforced concrete column and a steel beam in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The steel beam and column are modeled as three-dimensional solid parts. The steel bar ...

In this tutorial, the Simulation dynamic compression test of a steel column with the UHPC core in interaction with a concrete foundation in Abaqus has been investigated. The concrete foundation and column are modeled as three-dimensional solid parts. The steel column and steel stiffener angles are modeled as shell parts. ...

Column base connections are among the most critical components of Steel Moment Frames, their behavior profoundly influences the overall performance of SMFs. Early investigations on Column-base connections alongside remarkable experimental programs on large-scale specimens. have provided insight into their behavior and failure modes. These tests led to the development of ...

In this tutorial, the Simulation Pull-Out test of a ribbed steel bar from the UHPC part in Abaqus has been investigated. The steel bar is imported to Abaqus from the CAD software because of the complex geometry as a solid part. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. ...

In this tutorial, the Simulation air blast load over a reinforced concrete beam with a spiral GFRP bar in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part, the spiral GFRP is a solid part also. The steel reinforcements are modeled as three-dimensional wire parts. ...

In this tutorial, the fire analysis of a composite beam (RC concrete slab+ steel beam) under bending load in Abaqus has been done. The concrete slab is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts. The steel beam is modeled as a three-dimensional solid ...

In this tutorial, the Simulation compression test of a concrete column reinforced with GFRP bars and strips in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The GFRP bars and strips are modeled as three-dimensional solid parts. You can see a figure of the ...

In this tutorial, the Investigation on the repeated impact responses of circular concrete-filled double-tube (CFDT) members in Abaqus have been studied. The two concrete cores are modeled as three-dimensional solid parts. The two steel tubes are modeled as three-dimensional solid parts. The rigid hammer as an impact is used also. ...

In this tutorial, the Simulation cyclic loading of a steel beam-column joint filled with the UHPC and welded stiffeners in Abaqus has been done. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. The steel beam and column are modeled as three-dimensional shell parts. The stiffeners are modeled as three-dimensional ...

In this tutorial, the Finite element analysis of the progressive collapse of reinforced, Ultra-High-Performance-Concrete frame has been investigated. The UHPC frame is modeled as a three-dimensional solid part. The steel reinforcements are modeled as three-dimensional wire parts. You can see a figure of the assembled parts below Progressive collapse is ...

In this tutorial, the Simulation of a CEL large-scale bomb explosion (Nuclear detonation) near a building in Abaqus has been investigated. A nuclear explosion releases vast amounts of energy in the form of blasts, heat, and radiation. An enormous Shockwave reaches speeds of many hundreds of kilometers an hour. The blast ...

In this tutorial, the Simulation compression test of a composite column(wood-uhpc-steel cover) in Abaqus has been investigated. The wood core and Ulta-High-Performance-Concrete parts are modeled as three-dimensional solid parts. The steel cover is modeled as a shell part. You can see a figure of the assembled parts below Wood columns ...

In this tutorial, the Simulation Phantom aircraft collision with a concrete wall in Abaqus has been investigated. The concrete wall is modeled as a three-dimensional solid part. The Phantom is imported as an input geometry to Abaqus as a shell part. You can see a figure of the parts below ...

In this tutorial, the Simulation air blast analysis of a composite column(wood-concrete-CFRP) in Abaqus has been investigated. The wood is modeled as a three-dimensional solid part with two layers of tension and compression. The concrete is modeled as a three-dimensional solid part. The steel bars and strips are modeled as ...

In this tutorial, the Simulation bending test of a composite beam(wood-UHPC-Steel) in Abaqus has been done. The wood is modeled as a three-dimensional solid part with two layers, the top layer is in compression, and the bottom is in tension. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. The ...

In this tutorial, the  Simulation CEL explosion near a stone wall covered with cloth, and concrete in Abaqus has been investigated. The stone wall and cloth, concrete are modeled as three-dimensional solid parts. The TNT is a solid sphere, and the Eulerian domain is a 3D body. You can see ...

In this tutorial, the Simulation of RC Beams during Fire Events Using a Fully Coupled thermal stress Analysis in Abaqus has been studied. The concrete beam is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts. You can see a figure of the assembled parts ...

In this tutorial, the Simulation of the Push-Out test on a new shear connector of the I-Shape in Abaqus has been investigated. The concrete is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts. The steel beam and connector are modeled as three-dimensional solid part. ...

In this tutorial, the Simulation air blast load over a RC beam reinforced with Cloth Concrete cover in Abaqus has been done, The normal concrete core is modeled as a three-dimensional solid part. The cloth concrete part is modeled as a three-dimensional patrt. The steel bar and strips are modeled ...

In this tutorial, the Simulation CEL explosion inside the RC UHPC building in Abaqus-Damage investigation has been done The Ulta-High-Performance-Concrete(UPHC) building is modeled as a three-dimensional solid part. The reinforcements are modeled as wire part. The TNT is shpere part inside the Eulerian domain. You can see figures of the ...

In this tutorial, the Simulation compression test of a RC column with spiral CFRP with fully damaged behaviour in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The spiral CFRP is modeled as a three-dimensional solid part. The steel bar is modeled as a ...

In this tutorial, the Simulation air blast explosion over RC column with spiral strip and steel tube cover in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The spiral strips and bars are modeled as three-dimensional wire part. The steel tube as cover is ...

In this tutorial, the Air blast explosion over a rienforced concrete column with spiral CFRP strip in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel strips and bars are modeled as three-dimensional wire part. The spiral CFRP part is modeled as a ...

In this tutorial, the Simulation CEL explosion of steel-UHPC composite RC beam(column) with multiple encased steel profiles in Abaqus  has been done. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. The bar and strip are modeled as three-dimensional wire parts. The steel beam core and TNT part are modeled ...

In this tutorial, the Simulation compression test of CFRP composite spirals in circular hollow UHPC columns in Abaqus has been done. The Ultra-High-Performace-Concrete column is modeled as a three-dimensional solid part. The spiral CFRP part is modeled as a solid part, the longitudinal steel bar is modeled as a wire ...

In this tutorial, the Simulation dynamic bending test of steel-concrete composite beam(column) with multiple encased steel profiles in Abaqus has been done. The beam(column) part is modeled as a three-dimensional solid part, the two steel beam parts are  modeled as three-dimensional solid part. You can see a figure of the ...

In this tutorial, the  simulation of Damage prediction of concrete gravity dams subjected to underwater explosion shock loading has been done. The concrete dam is modeled as a three-dimensional solid part. The TNT, water, and air are modeled as eulerian part. The rock foundation is modeled as a three-dimensional solid ...

In this tutorial, the Simulation of concrete-encased CFST box stub columns under axial compression in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The steel pipes are modeled as three-dimensional solid part also,  and the steel bar and strips are modeled as the wire ...

In this tutorial, the Simulation RC beam column joint reinforced with steel plates and rods under vertical load in abaqus  has been investigated. The concrete beam-column is modeled as a three-dimensional solid part. The steel bar and strip are modeled as three-dimensional wire part. The steel plates and rods are ...

In this tutorial, the Simulation five point bending of a composite concrete beam(NSC+UHPFRC) in Abaqus has been done. The normal strength concrete beam as a cover is modeled as a three-dimensional solid part. The Ultra-High-Performace-Fiber-Reinforce-Concrete core is modeled as the a three-dimensional solid part. The steel bars and strips are ...

In this tutorial, the Simulation dynamic compression test of a RC column with UHPFRC core in Abaqus has been done, The concrete column is modeled as a three-dimensional solid part. The steel bar and strip are modeeld as three-dimensional wire paer. The Ultra-High-Performance-Fiber-Reinforce Concrete is modeled as a three-dimensional solid ...

In this tutorial, the Simulation dynamic four point bending test of a Gravity beam in Abaqus has been investigated. Gravity Beams, a term coined in this investigation, are those beams in which gravity is used to design the topology of beam form conjointly with the novel manufacturing strategy Fabric Formwork. ...

In this tutorial, Simulation low energy impact of a rigid hammer on the wood-cement-concrete panel in Abaqus has been investigated. The panel contians three layers, top layer is wood-cement part as a soild model, the second layer is normal strenght concrete as a solid part, and third layer is wood-cement ...

In this tutorial the Simulation rocket impact and explosion over a concrete panel in Abaqus has been investigated. The concrete panel is modeled as a three-dimensional solid part. The rocket is modeled as a three-dimensional shell part, and the TNT is modeeld as a solid part. You can see a ...

In this tutorial, the Simulation four point bending test of a foamed concrete beam reinforced with steel bars and bamboo fiber in Abaqus has been investigated. The foamed concrete part is modeled as a three-dimensional solid part. The bamboo composite is modeled as a three-dimensional shell part with some layers. ...

In this tutorial, the Simulation air blast explosion over a steel-UHPC-steel sandwich composite beam stud connectors in Abaqus has been studied. The two steel plates with studs are modeled as three-dimensional solid part. The UHPC is modeled as a three-dimensional solid part as a core of the sandwich beam. You ...

In this tutorial, the Simulation dynamic bending test of SCS sandwich beams with UHPFRC in Abaqus has been investigated. The upper and bottom steel plates with studs are modeled as three-dimensional solid part. The middle UHPFRC is modeled as a three-dimensional solid part. You can see a figure of the ...

In this tutorial, the Simulation cyclic loading of a steel beam embedded in a concrete block in Abaqus has been done. The steel beam (or column) is modeled as a three-dimensional shell part. The concrete block is modeled as a three-dimensional solid part. The half of the steel beam is ...

In this tutorial, the Numerical simulation of interlocking blocks under compression in Abaqus has been done. The blocks are modeled as three dimensional solid parts with interlocking surfaces. You can see a figure of the assembled parts below Masonry structure is one of the most predominant structures throughout the world ...

In this tutorial, the Simulation sequential CEL explosion in the depth of soil over the RC slab in Abaqus has been investigated. The concrete slab is modeled as three-dimensional solid part, the steel reinforcement is modeled as wire part. The Soil, and TNT are modeled as three-dimensional solid parts. The ...

In this tutorial, the Simulation UHPFRC beam with initial void reinforced with CFRP rod and Expoxy under dynamic bending has been investigated. The concrete beam, CFRP rod, epoxy glu are modeled as three-dimensional solid parts. Two rigid body as a hydraulic jacks also are modeled. You can see a figure ...

In this tutorial, the Simulation air blast explosion over the rebberized concrete column reinforced with green composite in Abaqus has been done. The rubberized concrete column is modeled as a three-dimensional solid part. The green composite with some layers is modeled as a three-dimensional shell part. The steel reinforcements are ...

In this tutorial, the Simulation dynamic bending test of a rubberized concrete beam reinforced with green composite  in abaqus has been investigated. The rubberized concrete beam is modeled as a three-diensional solid part. The green composite is modeled as a three-dimensional shell part with four layups. The steel bas and ...

In this tutorial the explosion simulation near the reinforced concrete wall with green composite-SPH method- has been investigated. The TNT part is modeled as a three-dimensional solid part. The concrete wall or slab is modeled as three-dimensional solid part, the green composite part with eight layers is modeld as three-dimensional ...