بایگانی برچسب: free abaqus tutorial

Introduction to Blast Resistance Behavior of Interior Voided Slab-Column Connections Using Steel Sheets and CFRP Reinforcement Background and Significance Modern structures, particularly those in high-risk environments, require enhanced resistance to extreme loading conditions such as blast loads. Slab-column connections are critical zones in reinforced concrete (RC) frames, often susceptible to ...

Flexural Behavior of Adhesively Bonded Cross-Laminated Timber–Ultra-High-Performance Concrete (CLT-UHPC) Composite Panels Introduction Composite structural systems combining cross-laminated timber (CLT) and ultra-high-performance concrete (UHPC) have gained attention due to their potential to enhance structural efficiency, sustainability, and performance. CLT provides a high strength-to-weight ratio, carbon sequestration benefits, and ease of prefabrication, while UHPC contributes ...

Introduction to Cyclic Loading Analysis of a Cracked Concrete Column Reinforced with GFRP Bars in Abaqus Cyclic loading analysis of damaged concrete columns reinforced with Glass Fiber-Reinforced Polymer (GFRP) bars is an important simulation for evaluating seismic performance and rehabilitation strategies. This analysis helps engineers understand how cracked concrete structures ...

Introduction to Numerical Study on CFRP-Lined Concrete Cylinder Pipe (CCP) Under Internal Explosion Concrete Cylinder Pipes (CCPs) are widely used in water transmission systems due to their high load-bearing capacity and durability. However, they are vulnerable to internal explosions caused by accidental gas ignition or deliberate attacks, leading to catastrophic ...

In this practical example, the Simulation shock pressure and shock-wave attenuation near a blast hole in rock in Abaqus has been investigated. The CEL approach is selected to model the blast load in the borehole. You can see a figure of the assembled parts below When an explosive detonates in ...

Introduction to Ceramic and Silicon Carbide Materials Ceramics are inorganic, non-metallic materials known for their high hardness, thermal stability, and chemical resistance. They are typically made by heating natural minerals (like clay) or synthetic powders at high temperatures (sintering). Silicon carbide is an advanced ceramic and semiconductor material composed of ...

Introduction to Ultra-High-Performance Concrete (UHPC) in Abaqus Ultra-high-performance concrete (UHPC) is an advanced cementitious material characterized by its exceptional strength, durability, and ductility. It typically has a compressive strength exceeding 150 MPa and can reach up to 250 MPa or higher, along with superior tensile strength and resistance to environmental ...

Introduction to Polymeric and Metal Foam Simulation in Abaqus Polymeric and metal foam are advanced materials widely used in industries such as aerospace, automotive, biomedical, and construction due to their unique properties, including high strength-to-weight ratios, energy absorption, and thermal and acoustic insulation. Simulating these materials in Abaqus, a powerful ...

In this tutorial, the Strengthening of reinforced concrete columns incorporating different configurations of stainless-steel plates has been investigated. The concrete column, steel plates, and rods are modeled as three-dimensional solid parts. The steel bar and strips are modeled as wire parts. You can see figures of the assembled parts below ...

In this tutorial, the Simulation of ceramic plates as shielding for concrete blocks against projectile penetration(SPH method) has been done. The ceramic plate and Ultra-High-Performance-Concrete are modeled as three-dimensional solid parts. The bullet is modeled as a solid part. You can see a figure of the assembled parts below In ...

In this tutorial, the Simulation deposition behavior of multi-particle impact in the cold spraying process in Abaqus has been investigated. The aluminum particles are modeled as three-dimensional solid parts. The aluminum target also is modeled as a three-dimensional solid part. You can see a figure of the assembled parts In ...

In this tutorial, the Simulation load bearing capacity of a composite joint between a reinforced concrete column and a steel beam in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The steel beam and column are modeled as three-dimensional solid parts. The steel bar ...

In this tutorial, the Simulation air blast load over a reinforced concrete beam with a spiral GFRP bar in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part, the spiral GFRP is a solid part also. The steel reinforcements are modeled as three-dimensional wire parts. ...

In this tutorial the Simulation Wood-Glue-CFRP beam under dynamic four points bending test in Abaqus has been investigated. The wood beam are modeled as three dimensional solid part, the adhesive parts are modeled as three-dimensional solid parts, the CFRP also si solid and the the roller are modeled as rigid ...