تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
خانه / بایگانی برچسب: abaqus tutorial

بایگانی برچسب: abaqus tutorial

Simulation rigid projectile impact to the ceramic-CFRP panel in Abaqus-Damage investigation

In this tutorial, the Simulation rigid projectile impact to the ceramic-CFRP panel in Abaqus-Damage investigation – has been done. The rigid projectile is modeled as a three-dimensional shell part. The ceramic is modeled as a three-dimensional thick solid part. The CFRP or carbon fiber is modeled as a three-dimensional shell ...

ادامه نوشته »

Simulation rigid impact to the composite panel(CFRP+TPU+AL) in Abaqus-Damage investigation

In this tutorial, the Simulation rigid impact to the composite panel(CFRP+TPU+AL) in Abaqus-Damage investigation – has been studied. The CFRP part is modeled as a shell part with eight layers. The Thermoplastic polyurethane is modeled as a three-dimensional solid part. The Aluminum part is modeled as a three-dimensional solid part. ...

ادامه نوشته »

Numerical analysis of tilted angle shear connectors in steel-concrete composite systems in Abaqus

In this tutorial, the Numerical analysis of tilted angle shear connectors in steel-concrete composite systems in Abaqus has been investigated. The concrete block is modeled as a three-dimensional solid part. The steel beam and steel angle connector are modeled as three-dimensional solid parts. Two rigid bodies are used as boundary ...

ادامه نوشته »

Simulation RC column retrofitted with CFRP and epoxy under compression load in Abaqus

In this tutorial, the Simulation RC column retrofitted with CFRP and epoxy under compression load in Abaqus has been done. The circular concrete column is modeled as a three-dimensional solid part. The sell strips and bars are modeled as three-dimensional wire parts. The CFRP is modeled as a conventional shell ...

ادامه نوشته »

Seismic behavior of RC exterior wide beam-column joints in Abaqus

In this tutorial, the Seismic behavior of RC exterior wide beam-column joints in Abaqus has been simulated. The concrete beam and column are modeled as three-dimensional solid parts. The steel bars and strips are modeled as three-dimensional wire parts. You can see a figure of the assembled parts below Reinforced ...

ادامه نوشته »

Learning all aspects of CEL, SPH, Acoustic, and CONWEP explosion modeling in Abaqus- Fifteen Hours simulation

In this course, we explained the Coupled Eulerian-Lagrangian, Smooth Particle Hydrodynamic, Acoustic, and CONWEP blast procedure in detail during twenty-three separate tutorials which you can see their title below. We provide this course because some people use our tutorials to create courses on Udemy but if you ask them questions ...

ادامه نوشته »

Simulation dynamic bending test of an interior voided RC UHPC beam in Abaqus

In this tutorial, the Simulation dynamic bending test of an interior voided RC UHPC beam in Abaqus has been studied. The Ultra-High-Performance Concrete beam is modeled as three-dimensional solid part with interior sphere voids. The steel bar and strips are modeled as three-dimensional wire parts. The rigid bodies are used ...

ادامه نوشته »

Simulation three-point bending test of the UHPC beam reinforced with Jute-Epoxy lamina in Abaqus

In this tutorial, the Simulation three-point bending test of the UHPC beam reinforced with Jute-Epoxy lamina in Abaqus has been investigated. The UHPC beam is modeled as a three-dimensional solid part. The Jute-Epoxy lamina is modeled as a three-dimensional shell part with four layers. A rigid body shell part is ...

ادامه نوشته »

Simulation ice breaking by using brittle damage criterion in Abaqus

In this tutorial, the Simulation ice-breaking by using brittle damage criterion in Abaqus has been investigated. The ice part is modeled as a three-dimensional solid part and the steel part as a rough body is modeled as a three-dimensional solid part. You can see a figure of the assembled parts ...

ادامه نوشته »

Simulation steel projectile impact on the Acrylonitrile butadiene styrene(ABS) plate in Abaqus

In this tutorial, the Simulation steel projectile impact on the Acrylonitrile butadiene styrene(ABS) plate in Abaqus has been investigated. Polymers are often used in applications where impact resistance is required. In this context, specific polymers such as  ABS (acrylonitrile butadiene styrene) have been created with rubber particles in order to ...

ادامه نوشته »

Simulation repeated impact of the rigid body to the steel box in Abaqus

In this tutorial, the simulation repeated the impact of the rigid body to the steel box in Abaqus has been investigated. The steel box is modeled as a three-dimensional shell part and the rigid projectile is modeled as a rigid shell part. You can see a figure of the assembled ...

ادامه نوشته »

Simulation dental implant insertion in Abaqus

In this tutorial, the simulation dental implant insertion in Abaqus is investigated. Successful osseointegration is a degree of implant stability which occurs after implant integration. This end result is related to two terms, namely primary and secondary implant stability. Primary stability characterizes the mechanical engagement of the implant right after ...

ادامه نوشته »

Simulation ultra high performance fiber reinforced concrete beam under four points bending in Abaqus

In this tutorial, the Simulation ultra-high-performance fiber-reinforced concrete beam under four points bending in Abaqus has been investigated. Extensive research and development efforts, over the past three decades, to improve properties of concrete have led to the emergence of ultra-high performance concrete(UHPC). UHPC possesses very high compressive strength, good tensile ...

ادامه نوشته »

Simulation shear failure of two steel plates with bolt connection in Abaqus

In this tutorial, the Simulation shear failure of two steel plates with bolt connection in Abaqus has been investigated. The steel plates are modeled as a three-dimensional solid part The bolts with different sizes are modeled as a three-dimensional solid part. You can see a figure of the assembled part ...

ادامه نوشته »

Simulation blast explosion over the composite column in Abaqus- Damage investigation

In this tutorial, the Simulation blast explosion over the composite column in Abaqus- Damage investigation – has been studied. The model contains three deformable parts. The outer steel box as a cover is modeled as a three-dimensional shell, the middle concrete is modeled as a three-dimensional solid part and the ...

ادامه نوشته »

Numerical simulation of reinforced bricks masonry beams using GFRP reinforcement in Abaqus

In this tutorial, the numerical simulation of reinforced bricks masonry beams using GFRP reinforcement in Abaqus has been investigated. The bricks are modeled as three-dimensional solid part and GFRP sheets are modeled as three-dimensional shell parts. You can see a figure of the assemble parts at below Natural stone structures ...

ادامه نوشته »

Simulation flexural behavior of the steel beam reinforced with CFRP in Abaqus

In this tutorial, the Simulation flexural behavior of the steel beam reinforced with CFRP in Abaqus has been investigated. The steel beam and CFRP sheet are modeled as three-dimensional shell parts. The rigid bodies are modeled as a discrete rigid body. You can see a figure of the assembled parts ...

ادامه نوشته »

Simulation concrete beam under static and dynamic bending in Abaqus

In this tutorial, the Simulation concrete beam under static and dynamic bending in Abaqus has been done. The concrete beam is modeled as a three- dimensional solid part and five rigid parts as forces and supporters bodies are used. You can see a figures of the assembled parts at below ...

ادامه نوشته »

ٍSimulation of p-section concrete beams under contact explosion(CEL) conditions in Abaqus

In this tutorial Simulation of p-section concrete beams under contact explosion(CEL) conditions in Abaqus has been studied. Reinforced concrete bridges are the most common type of bridges and have a simple structure, low cost and long durability. Among these bridges, reinforced concrete bridges composed of p-section bridge components are among the ...

ادامه نوشته »

Prediction model of depth of penetration for alumina ceramics under garnet impact in Abaqus

In this tutorial Prediction model of depth of penetration for alumina ceramics under garnet impact in Abaqus has been studied .The target and projectile were modeled as three dimensional parts .The JH-2 constitutive model was proposed to describe the response of ceramic materials to large strain rate. The JH-2 constitutive model ...

ادامه نوشته »
تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.