تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
خانه / بایگانی برچسب: RC beam in Abaqus

بایگانی برچسب: RC beam in Abaqus

Simulation RC beam column joint reinforced with steel plates and rods under vertical load in abaqus

In this tutorial, the Simulation RC beam column joint reinforced with steel plates and rods under vertical load in abaqus  has been investigated. The concrete beam-column is modeled as a three-dimensional solid part. The steel bar and strip are modeled as three-dimensional wire part. The steel plates and rods are ...

ادامه نوشته »

Simulation RC beam under repeated impact of the rigid hammer in Abaqus

In this tutorial, the Simulation RC beam under the repeated impact of the rigid hammer in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The steel rebar and strips are modeled as three-dimensional wire parts. The rigid hammer is modeled as a three-dimensional rigid ...

ادامه نوشته »

Seismic behavior of RC exterior wide beam-column joints in Abaqus

In this tutorial, the Seismic behavior of RC exterior wide beam-column joints in Abaqus has been simulated. The concrete beam and column are modeled as three-dimensional solid parts. The steel bars and strips are modeled as three-dimensional wire parts. You can see a figure of the assembled parts below Reinforced ...

ادامه نوشته »

Abaqus Concrete Structures- Lecture contains all thing about concrete-More than ten hours of simulation

In this lecture through Twenty step by step tutorial, many aspects of the concrete structure like a beam, RC beam and column, normal concrete, UHPC, and UHPFRC concrete, composite beam, and column, cyclic loading over the RC beam and column, CFDST and CFST column, ECC beam-column joint, high strength concrete ...

ادامه نوشته »

Simulation of low energy impact on the RC beam and residual displacement investigation in Abaqus

In this tutorial, the Simulation of low energy impact on the RC beam and residual displacement investigation in Abaqus has been done. The concrete beam is modeled as a three-dimensional solid part. The steel bars and strips are modeled as three-dimensional wire parts. The hammer is modeled as a rigid ...

ادامه نوشته »

Simulation dynamic bending of RC beams strengthened with CFRP rods and Epoxy glue in Abaqus

In this tutorial, the Simulation dynamic bending of RC beams strengthened with CFRP rods and Epoxy glue in Abaqus has been done. The concrete beam is modeled as a three-dimensional solid part. The CFRP rod and epoxy glue are modeled as three-dimensional solid parts. The steel bars and strips are ...

ادامه نوشته »

Simulation dynamic pullout of a steel plate from the RC beam in Abaqus

In this tutorial, the Simulation dynamic pullout of a steel plate from the RC beam in Abaqus has been investigated. The steel plate is modeled as a three-dimensional solid part. The concrete beam is modeled as a three-dimensional solid part. The bars and strips are modeled as three-dimensional wire parts. ...

ادامه نوشته »

Simulation four points bending of an RC beam strengthened with CFRP sheet in Abaqus

In this tutorial, the simulation four points bending of an RC beam strengthened with CFRP sheet in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The strips and bars are modeled as three-dimensional wire part. The CFRP sheet is modeled as a three-dimensional shell ...

ادامه نوشته »

Simulation of concrete cover separation failure in FRP plated RC beam in Abaqus

In this tutorial Simulation of concrete cover separation failure in FRP plated RC beam in Abaqus has been studied.The infrastructures in developed countries are aging and in addition changes in their using purposes, increase of load level, constructional faults and damages or deterioration demand adequate maintenance and the upgrading of ...

ادامه نوشته »
تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
enemad-logo