تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
خانه / بایگانی برچسب: abaqus simulation (صفحه 5)

بایگانی برچسب: abaqus simulation

شبیه سازی تست فشار ستون بتنی فوق توانمند محاط شده در لوله فلزی در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی تست فشار ستون بتنی فوق توانمند محاط شده در لوله فلزی در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی می باشد و هسته بتنی ستون به صورت سالید طراحی شده است. لوله فولادی بیرونی نیز به صورت سه بعدی و ...

ادامه نوشته »

Simulation dynamic pullout process of a steel bar form the concrete by using cohesive surface interaction in Abaqus

In this tutorial, the Simulation dynamic pullout process of a steel bar form the concrete by using cohesive surface interaction in Abaqus has been studied. The steel bar and concrete are modeled as three-dimensional solid parts. You can see a figure of the assembled part below One of the main ...

ادامه نوشته »

شبیه سازی دینامیکی بیرون کشیدن میلگرد از بتن با متریال مدل CDP و با روش تماس سطوح چسبنده در آباکوس

در این ویدئوی آموزشی به شبیه سازی دینامیکی بیرون کشیدن میلگرد از بتن با متریال مدل CDP و با روش تماس سطوح چسبنده در نرم افزار آباکوس پرداخته ایم. مدل سازی به صورت سه بعدی و تقارنی بوده که از نصف مدل با در نظر گرفتن شرایط تقارنی استفاده شده ...

ادامه نوشته »

Simulation Static tensile test of the concrete piece in the Abaqus

In this tutorial, the Simulation Static tensile test of the concrete piece in the Abaqus has been studied. The concrete part is modeled as a three-dimensional solid part. You can see a figure of the assemble part below Concrete is a strongly heterogeneous material, which exhibits a complex nonlinear mechanical ...

ادامه نوشته »

شبیه سازی تست کشش استاتیکی یک قطعه بتنی در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی تست کشش استاتیکی یک قطعه بتنی در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل یک پارت با ناحیه نازک شده میانی می باشد. پارت بتن به صورت سالید طراحی شده است. در شکل زیر می توانید نمایی ...

ادامه نوشته »

Simulation masonry wall under compression and transverse load in Abaqus-Macro model

In this tutorial, the Simulation masonry wall under compression and transverse load in Abaqus-Macro model has been studied. The wall is modeled as a three-dimensional solid part. The beam is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below In early stages of ...

ادامه نوشته »

شبیه سازی بارگذاری فشاری و عرضی یک دیوار بنایی به صورت ماکرو در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی بارگذاری فشاری و عرضی یک دیوار بنایی به صورت ماکرو در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی و اجزا به صورت سالید ترسیم شده اند. هندسه شامل دیوار و دو تیر بتنی در بالا و پایین دیوار می باشد. ...

ادامه نوشته »

Simulation of hollow core square reinforced concrete column wrapped with CFRP under compression in Abaqus

In this tutorial, the Simulation of hollow core square reinforced concrete columns wrapped with CFRP under compression in Abaqus has been studied. The concrete part is modeled as a three-dimensional solid part. The CFRP box in modeled as a three-dimensional shell part. The steel bars and strips are modeled as ...

ادامه نوشته »

شبیه سازی ستون بتنی توخالی تقویت شده با میلگرد و CFRP تحت بار فشاری در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی ستون بتنی توخالی تقویت شده با میلگرد و CFRP تحت بار فشاری در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و در آن ستون بتنی به صورت سه بعدی و سالید طراحی شده است. میلگردها و خاموت ها نیز ...

ادامه نوشته »

Simulation four point bending of the CFRP sheet with six layers (inter laminar cohesive behavior) in Abaqus

In this tutorial, the Simulation four point bending of the CFRP sheet with six layers (inter laminar cohesive behavior) in Abaqus has been studied. The CFRP layers are modeled as three-dimensional solid part. Two rigid bodies were used as hydraulic jack to apply the load. You can see a figure ...

ادامه نوشته »

شبیه سازی خمش چهار محوره ورق شش لایه CFRP با در نظر گرفتن رفتار چسبندگی بین لایه ای در آباکوس

در این ویدئوی آموزشی به شبیه سازی خمش چهار محوره ورق شش لایه CFRP با در نظر گرفتن رفتار چسبندگی بین لایه ای در آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی می باشد که شامل شش لایه ورق CFRP و دو جسم صلب به منظور اعمال نیرو می باشد. ...

ادامه نوشته »

Simulation water jet penetration into the stone piece in Abaqus by using SPH method

In this tutorial, the Simulation water jet penetration into the stone piece in Abaqus by using SPH method  has been studied. The stone is modeled as a three-dimensional solid part. The water column is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below ...

ادامه نوشته »

شبیه سازی اثر واتر جت(SPH) روی یک قطعه سنگ و بررسی آسیب در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی اثر واتر جت(SPH) روی یک قطعه سنگ و بررسی آسیب در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و سنگ به صورت یک پارت سالید طراحی شده است. آب به صورت یک استوانه به صورت سه بعدی و سالید ...

ادامه نوشته »

Simulation Composite beam(Concrete and steel beam) under fire condition in Abaqus-Thermal and Stress analysis

In this tutorial, the Simulation Composite beam(Concrete and steel beam) under fire condition in Abaqus-Thermal and Stress analysis- has been studied. The concrete and steel beam are modeled as three-dimensional solid parts. You can see a figure of the assembled parts below Reinforced concrete (RC) structural members, when exposed to ...

ادامه نوشته »

شبیه سازی آتش سوزی(حرارتی-سازه ای) روی تیر بتنی با هسته تیر فولادی در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی آتش سوزی(حرارتی-سازه ای) روی تیر بتنی با هسته تیر فولادی در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و پارت های تیر بتنی و فولادی به صورت سالید و تغییرشکلپذیر ترسیم شده اند. تحلیل به صورت شبیه سازی متوالی ...

ادامه نوشته »

Simulation of steel bolted double angle connections under dynamic load in Abaqus-Failure analysis

In this tutorial, the simulation of steel bolted double angle connections under dynamic load in Abaqus-Failure analysis- has been studied. The beam and column are modeled as three-dimensional solid part. The bolts are modeled as three-dimensional solid part. You can see a figure of the assembled parts below Connections have ...

ادامه نوشته »

شبیه سازی پارگی پیچ در اتصال تیر به ستون با نبشی تحت بار دینامیکی در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی پارگی پیچ در اتصال تیر به ستون با نبشی تحت بار دینامیکی در نرم افزار آباکوس پرداخته ایم. مدل سازی به صورت سه بعدی می باشد. تیر و ستون به صورت سه بعدی و سالید طراحی شده اند. پیچ ها نیز به صورت ...

ادامه نوشته »

Simulation steel projectile impact to the water covered by ice layer in Abaqus

In this tutorial, the Simulation steel projectile impact to the water covered by ice layer in Abaqus  has been studied. The steel projectile is modeled as a three-dimensional solid part. The water and air are modeled as three-dimensional eulerian part. The ice is modeled as a three-dimensional solid part. You ...

ادامه نوشته »

شبیه سازی نفوذ پرتابه فولادی در آب پوشیده شده از لایه یخ در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی نفوذ پرتابه فولادی در آب پوشیده شده از لایه یخ در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و پرتابه فولادی به صورت یک مدل سالید و سه بعدی طراحی شده است. لایه یخ با استفاده از یک پارت ...

ادامه نوشته »

Simulation dynamic tensile test of an aluminum piece by using ductile,shear, and MSFLD damage criterion in Abaqus

In this tutorial, the Simulation dynamic tensile test of an aluminum piece by using ductile, shear, and MSFLD damage criterion in Abaqus has been studied. The aluminum part is modeled as a three-dimensional solid part. You can see a figure of the assembled below The aluminum alloys may fail due ...

ادامه نوشته »

شبیه سازی تست کشش دینامیکی قطعه آلومینیوم با استفاده از معیار های آسیب در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی تست کشش دینامیکی قطعه آلومینیوم با استفاده از معیار های آسیب در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و از یک پارت سالید آلمینیومی به منظور بررسی جدایش و شکست دینامیکی قطعه تحت اثر کشش استفاده شده است. ...

ادامه نوشته »

Simulation dynamic pullout of a steel plate from the RC beam in Abaqus

In this tutorial, the Simulation dynamic pullout of a steel plate from the RC beam in Abaqus has been investigated. The steel plate is modeled as a three-dimensional solid part. The concrete beam is modeled as a three-dimensional solid part. The bars and strips are modeled as three-dimensional wire parts. ...

ادامه نوشته »

شبیه سازی بیرون کشیدن ورق فولادی از تیر بتنی تقویت شده با میلگرد در آباکوس-بررسی آسیب

در این ویدئوی آموزشی به شبیه سازی بیرون کشیدن ورق فولادی از تیر بتنی تقویت شده با میلگرد در نرم افزار آباکوس-بررسی آسیب- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و ورق فولادی به صورت یک مدل سالید و سه بعدی، تیر بتنی به صورت سالید و سه بعدی ...

ادامه نوشته »

Abaqus Welding Package- Simulation various welding process in Abaqus

In this package, you can find ten tutorials about the welding process in Abaqus like friction stir welding, pipe welding, plate welding,…You can find each tutorial separately on the website. This package contains the below list Simulation thermal stress analysis of arc welding between two pipes by using DFLUX subroutine ...

ادامه نوشته »

Simulation CEL explosion over the composite panel(Concrete-Steel bar-Steel sheet) in Abaqus

In this tutorial, the Simulation CEL explosion over the composite panel(Concrete-Steel bar-Steel sheet) in Abaqus has been done. The concrete is modeled as three dimensional solid part. The TNT and steel sheet are modeled as a three-dimensional solid part. The steel bars are modeled as three-dimensional wire part. The Eulerian ...

ادامه نوشته »

شبیه سازی انفجار به روش کوپل اویلری لاگرانژی روی یک پنل مرکب(بتن-میلگرد-ورق فولادی) در آباکوس

در این ویدئوی آموزشی به شبیه سازی انفجار به روش کوپل اویلری لاگرانژی روی یک پنل مرکب(بتن-میلگرد-ورق فولادی) در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل پارت هدف بتنی به صورت سه بعدی و سالید، پارت ورق فولادی به صورت سه بعدی و سالید ...

ادامه نوشته »

Simulation of Stud Connected Steel-UHPC Composite Girders Subjected to four-point bending in Abaqus

In this tutorial, Simulation of Stud Connected Steel-Concrete Composite Girders Subjected to four-point bending in Abaqus has been studied. The performance of steel-concrete composite (SCC) girders for static and dynamic loads depends significantly on the force transfer mechanism at the interface between steel beam and concrete. Stud connected SCC girders consist ...

ادامه نوشته »

شبیه سازی خمش چهار نقطه ای تیر فولادی-بتن فوق توانمند به همراه گل میخ در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی خمش چهار نقطه ای تیر فولادی-بتن فوق توانمند به همراه گل میخ در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی می باشد و پارت تیر فولادی به همراه گل میخ ها به صورت سه بعدی و سالید ترسیم شده اند. ...

ادامه نوشته »

Simulation dynamic bolt failure (bolt and steel plates joint) in Abaqus

In this tutorial, the Simulation dynamic bolt failure (bolt and steel plates joint) in Abaqus has been studied. The upper and bottom steel plates are modeled as three-dimensional solid parts. The bolts are modeled as three-dimensional solid parts. You can see a figure of the assembled parts below. Two main ...

ادامه نوشته »

شبیه سازی پارگی اتصال پیچی دو ورق تحت کشش در نرم افزار آباکوس- تحلیل دینامیکی

در این ویدئوی آموزشی به شبیه سازی پارگی اتصال پیچی دو ورق تحت کشش در نرم افزار آباکوس- تحلیل دینامیکی- پرداخته ایم. مدلسازی به صورت سه بعدی بوده که شامل دو پارت ورق فولادی رویی و زیرین می باشد که به صورت سالید و تغییر شکلپذیر ترسیم شده اند. پیچ ...

ادامه نوشته »

Simulation dynamic failure behavior of steel beam-to-column bolted connections in Abaqus

In this tutorial, the Simulation dynamic failure behavior of steel beam-to-column bolted connections in Abaqus has been investigated. Stainless steel displays numerous desirable properties which motivated many researchers to investigate its use in structural applications. Despite having comparatively high initial cost, its excellent corrosion resistance; outstanding durability; superior response to ...

ادامه نوشته »

شبیه سازی اتصال تیر به ستون فولادی با نبشی و پیچ تحت بار دینامیکی در آباکوس- بررسی آسیب

در این ویدئوی آموزشی به شبیه سازی اتصال تیر به ستون فولادی با نبشی و پیچ تحت بار دینامیکی در آباکوس- بررسی آسیب- پرداخته ایم. مدلسازی به صورت سه بعدی می باشد. پارت ستون و تیر فولادی به صورت سه بعدی و سالید ترسیم شده اند. پارت نبشی و پیچ ...

ادامه نوشته »

Simulation cold spray process of steel particle on the Inconel surface by using ALE method in Abaqus

In this tutorial, the Simulation cold spray process of steel particle on the Inconel surface by using the ALE method in Abaqus has been studied. The steel particle is modeled as a three-dimensional solid part. The Nickel-Chromium(Inconel) part is modeled as a three dimensional solid part. You can see a ...

ادامه نوشته »

شبیه سازی پاشش سرد ذرات فولاد به سطح آلیاژ نیکل-کروم در نرم افزار آباکوس-مقیاس میکرو

در این ویدئوی آموزشی به شبیه سازی پاشش سرد ذرات فولاد به سطح آلیاژ نیکل-کروم در نرم افزار آباکوس-مقیاس میکرو- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و ذره فولادی به صورت یک کره سه بعدی و سالید با شعاع چهل میکرو متر طراحی شده است. پارت هدف یا ...

ادامه نوشته »

Simulation pull-out process of the deformed steel bar from the concrete in Abaqus

In this tutorial, the Simulation pull-out process of the deformed steel bar from the concrete in Abaqus has been investigated. The goal of this simulation is the damage and failure zone analysis in the concrete slab. The concrete part is modeled as a three-dimensional solid part. The deformed steel bar ...

ادامه نوشته »

شبیه سازی بیرون کشیدن میلگرد از بتن به صورت دینامیکی در نرم افزار آباکوس-بررسی تخریب بتن

در این ویدئوی آموزشی به شبیه سازی بیرون کشیدن میلگرد از بتن به صورت دینامیکی در نرم افزار آباکوس-بررسی تخریب بتن- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و پارت بتن به صورت سالید و سه بعدی طراحی شده است. به دلیل پیچیدگی هندسه میلگرد آج دار، هندسه مربوط ...

ادامه نوشته »

Simulation fire analysis of the concrete beam in the Abaqus- Temperature and Stress analysis

In this tutorial, the Simulation fire analysis of the concrete beam in the Abaqus-Temperature and Stress analysis- has been studied. Owing to the low thermal conductivity of concrete, the concrete cover acts as fire insulation to reinforcing bars in reinforced concrete (RC) elements. In real fire incidents, concrete buildings generally ...

ادامه نوشته »

شبیه سازی آتش سوزی روی یک تیر بتنی با متریال مدل CDP در آباکوس- بررسی تبدیل حرارت به تنش

در این ویدئوی آموزشی به شبیه سازی آتش سوزی روی یک تیر بتنی با متریال مدل CDP در نرم افزار آباکوس- بررسی تبدیل حرارت به تنش- پرداخته ایم.مدلسازی به صورت سه بعدی بوده و در آن از یک تیر بتنی به صورت سه بعدی و سالید استفاده شده است. در ...

ادامه نوشته »

Simulation four-point bending of the UHPC slab reinforced with steel bars and GFRP sheet in Abaqus

In this tutorial, the Simulation four-point bending of the UHPC slab reinforced with steel bars and the GFRP sheet in Abaqus has been investigated. The UHP concrete slab is modeled as a three-dimensional solid part. The steel bars are modeled as three-dimensional wire parts. The GFRP sheet with eight layers ...

ادامه نوشته »

شبیه سازی خمش چهار محوره دال بتنی فوق توانمند تقویت شده با میلگرد و ورق GFRP در آباکوس

در این ویدئوی آموزشی به شبیه سازی خمش چهار محوره دال بتنی فوق توانمند تقویت شده با میلگرد و ورق GFRP در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و دال بتنی فوق توانمند به صورت یک پارت سه بعدی و سالید، میلگردها به صورت یک ...

ادامه نوشته »

Simulation sequential air blast explosion over the concrete slab reinforced with CFRP sheet in Abaqus

In this tutorial, the Simulation sequential air blast explosion over the concrete slab reinforced with CFRP sheet in Abaqus has been studied. The concrete slab is modeled as a three-dimensional solid part. The CFRP sheet is modeled as a three-dimensional shell part. You can see figures of the assembled parts ...

ادامه نوشته »

شبیه سازی انفجار در هوا به صورت پی در پی روی یک دال بتنی تقویت شده با CFRP در آباکوس

در این ویدئو به شبیه سازی انفجار در هوا به صورت پی در پی روی یک دال بتنی تقویت شده با CFRP در نرم افزار آباکوس پرداخته ایم. منظور از مدلسازی به صورت پی در پی در واقع انتقال نتایج آنالیز اولیه به آنالیز دوم و آنالیز دوم به آنالیز ...

ادامه نوشته »

Simulation axial compression of the damaged concrete column with initial residual stress reinforced with CFRP in Abaqus

In this tutorial, the Simulation axial compression of the damaged concrete column with initial residual stress reinforced with CFRP in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The CFRP box is modeled as a three-dimensional shell part. In the first simulation of the ...

ادامه نوشته »

شبیه سازی ستون بتنی با آسیب و تنش پسماند اولیه تحت بار محوری،تقویت شده با CFRP در آباکوس

در این ویدئوی آموزشی به شبیه سازی ستون بتنی با آسیب و تنش پسماند اولیه تحت بار محوری،تقویت شده با CFRP در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و ستون بتنی به صورت سه بعدی و سالید و صفحات کامپوزیتی نیز به صورت شل سه ...

ادامه نوشته »

Simulation damaged concrete beam with initial residual stress reinforced with CFRP sheet under bending load in Abaqus

In this tutorial, the Simulation damaged concrete beam with initial residual stress reinforced with CFRP sheet under bending load in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The CFRP sheet is model as a three-dimensional shell part. In this tutorial, at the first ...

ادامه نوشته »

شبیه سازی تقویت تیر بتنی با آسیب و تنش پسماند اولیه با ورق CFRP تحت خمش چهار نقطه ای در آباکوس

در این ویدئوی آموزشی به شبیه سازی تقویت تیر بتنی با آسیب و تنش پسماند اولیه با ورق CFRP تحت خمش چهار نقطه ای در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل دو پارت تیر بتنی به صورت سه بعدی و سالید و پارت ...

ادامه نوشته »

Simulation of ice damage under underwater near-field explosion by using the CEL method in Abaqus

In this tutorial, the Simulation of ice damage under underwater near-field explosion by using the CEL method in Abaqus has been investigated. The ice is modeled as a three-dimensional solid part. The TNT, air, and water are modeled as three-dimensional Eulerian parts. Due to the extremely short reaction time of ...

ادامه نوشته »

شبیه سازی انفجار زیر آب در نزدیکی لایه یخ به روش کوپل اویلری-لاگرانژی در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی انفجار زیر آب در نزدیکی لایه یخ به روش کوپل اویلری-لاگرانژی در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و در این تحلیل یخ به صورت مدل سالید و سه بعدی، تی ان تی، هوا و آب نیز به ...

ادامه نوشته »

Simulation internal explosion inside the rock by using coupled Eulerian-Lagrangian method in Abaqus

In this tutorial, the Simulation internal explosion inside the rock by using the coupled Eulerian-Lagrangian method in Abaqus has been studied. The rock and TNT are modeled as three-dimensional solid parts. The Eulerian domain is modeled as a three-dimensional Eulerian part. You can see a figure of the assembled parts ...

ادامه نوشته »

شبیه سازی انفجار به روش کوپل اویلری-لاگرانژی درون یک قطعه سنگ در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی انفجار به روش کوپل اویلری-لاگرانژی درون یک قطعه سنگ در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل سه هندسه می باشد که پارت سنگ به صورت سه بعدی و تغییر شکلپذیر، بارت تی ان تی به صورت سه بعدی و تغییر شکلپذیر و ...

ادامه نوشته »
تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
enemad-logo