تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
خانه / بایگانی برچسب: failure (صفحه 5)

بایگانی برچسب: failure

Simulation CEL explosion over a steel column and concrete foundation in interaction with soil in Abaqus

In this tutorial, the Simulation CEL explosion over a steel column and concrete foundation in interaction with soil in Abaqus has been studied. The steel column and steel plate are modeled as a three-dimensional solid part. The TNT and soil are modeled as a three-dimensional part. The embedded beam inside ...

ادامه نوشته »

Simulation shear failure of two steel plates with bolt connection in Abaqus

In this tutorial, the Simulation shear failure of two steel plates with bolt connection in Abaqus has been investigated. The steel plates are modeled as a three-dimensional solid part The bolts with different sizes are modeled as a three-dimensional solid part. You can see a figure of the assembled part ...

ادامه نوشته »

شبیه سازی اتصال دو ورق با پیچ و بررسی پارگی آن تحت کشش در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی اتصال دو ورق با پیچ و بررسی پارگی آن تحت کشش در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل دو ورق فولادی به صورت تغییر شکلپذیر و سالید می باشد. پیچ ها دارای ابعاد متفاوتی بوده  که ...

ادامه نوشته »

Simulation CEL explosion inside the steel pipe embedded in the depth of soil in Abaqus

In this tutorial, the Simulation CEL explosion inside the steel pipe embedded in the depth of soil in Abaqus has been investigated. The pipe is modeled as a three-dimensional shell part. The TNT, soil, and air are modeled as a three-dimensional solid part. The Eulerian part is model as a ...

ادامه نوشته »

شبیه سازی انفجار به روش کوپل اویلری لاگرانژی درون یک لوله فولادی مدفون در خاک در آباکوس

در این ویدئوی آموزشی به شبیه سازی انفجار به روش کوپل اویلری لاگرانژی درون یک لوله فولادی مدفون در خاک در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و لوله به صورت پارت شل و تغییر شکلپذیر، تی ان تی به صورت سالید ، هو به ...

ادامه نوشته »

Simulation blast explosion over the composite column in Abaqus- Damage investigation

In this tutorial, the Simulation blast explosion over the composite column in Abaqus- Damage investigation – has been studied. The model contains three deformable parts. The outer steel box as a cover is modeled as a three-dimensional shell, the middle concrete is modeled as a three-dimensional solid part and the ...

ادامه نوشته »

Numerical simulation of reinforced bricks masonry beams using GFRP reinforcement in Abaqus

In this tutorial, the numerical simulation of reinforced bricks masonry beams using GFRP reinforcement in Abaqus has been investigated. The bricks are modeled as three-dimensional solid part and GFRP sheets are modeled as three-dimensional shell parts. You can see a figure of the assemble parts at below Natural stone structures ...

ادامه نوشته »

Simulation high velocity impact of the steel projectile on the composite panel(Steel-Concrete-Epoxy glass) in Abaqus

In this tutorial, the Simulation high-velocity impact of the steel projectile on the composite panel(Steel-Concrete-Epoxy glass) in Abaqus has been investigated. The steel projectile is modeled as a cylindrical solid part. The steel plate as a first layer of the panel is modeled as a three-dimensional part. The concrete as ...

ادامه نوشته »

Simulation flexural behavior of the steel beam reinforced with CFRP in Abaqus

In this tutorial, the Simulation flexural behavior of the steel beam reinforced with CFRP in Abaqus has been investigated. The steel beam and CFRP sheet are modeled as three-dimensional shell parts. The rigid bodies are modeled as a discrete rigid body. You can see a figure of the assembled parts ...

ادامه نوشته »

شبیه سازی تست خمش تیر فولادی تقویت شده با CFRP در نرم افزار آباکوس

در این ویدئو آموزشی به شبیه سازی تست خمش تیر فولادی تقویت شده با CFRP در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده که در آن تیر فولادی و ورق CFRP به صورت پارت شل بعدی ترسیم شده اند. اجسام تکیه گاهی و جسم وارد کننده ...

ادامه نوشته »

Simulation five points bending of the concrete beam in Abaqus

In this tutorial, Simulation five points bending of the concrete beam in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The rebar inside the concrete beam is modeled as a three-dimensional wire part. The rigid shell body is used to model the boundary zone ...

ادامه نوشته »

شبیه سازی خمش پنج نقطه ای تیر بتنی مسلح با میلگرد در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی خمش پنج نقطه ای تیر بتنی مسلح با میلگرد در نرم افزار آباکوس پرداخته ایم. مدل شامل تیر بتنی سه بعدی و تغییر شکلپذیر، میلگردها به صورت پارت وایر سه بعدی و اجسام صلب در نقش تکیه گاهها و اعضای وارد کننده نیرو ...

ادامه نوشته »

Simulation cyclic loading over steel beam column structure reinforced with CFRP in Abaqus

In this tutorial, Simulation cyclic loading over the steel beam-column structure reinforced with CFRP in Abaqus has been investigated. The steel beam and column are modeled as a three-dimensional shell part. The CFRP plates are modeled as a planar shell part. You can see a figure of the assembled parts ...

ادامه نوشته »

شبیه سازی بارگذاری تکراری روی یک تیر و ستون تقویت شده با FRP در آباکوس

در این ویدئوی آموزشی به شبیه سازی بارگذاری تکراری روی یک تیر و ستون تقویت شده با FRP در نرم افزار آباکوس پرداخته ایم.مدلسازی به صورت سه بعدی بوده و تحلیل شامل هندسه ستون به صورت شل،تیر فلزی به صورت شل و دو ورق CFRP در محل اتصال تیر به ...

ادامه نوشته »

Simulation bolt failure in the bolted joints in Abaqus

In this tutorial, simulation of bolt failure in the bolted joints in Abaqus has been done. The two steel plates and the bolt are modeled as a three-dimensional solid part. You can see a figure of the assembled parts at below To obtain failure, the ductile damage criterion is used ...

ادامه نوشته »

شبیه سازی اتصال دو ورق با پیچ تحت کشش در نرم افزار آباکوس- بررسی آسیب

در این ویدئوی آموزشی به شبیه سازی اتصال دو ورق با پیچ تحت کشش در نرم افزار آباکوس- بررسی آسیب- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و مساله شامل سه پارت می باشد. دو ورق سوراخ دار در بالا و پایین و در محل سوراخ نیز یک پیج ...

ادامه نوشته »

Simulation concrete beam under static and dynamic bending in Abaqus

In this tutorial, the Simulation concrete beam under static and dynamic bending in Abaqus has been done. The concrete beam is modeled as a three- dimensional solid part and five rigid parts as forces and supporters bodies are used. You can see a figures of the assembled parts at below ...

ادامه نوشته »

شبیه سازی تست خمش یک تیر بتنی در دو حالت بارگذاری استاتیکی و دینامیکی در آباکوس

در این ویدئوی آموزشی به شبیه سازی تست خمش یک تیر بتنی در دو حالت بارگذاری استاتیکی و دینامیکی در نرم افزار آباکوس پرداخته ایم.مجموعه شامل یک قطعه تیر بتنی که به صورت سه بعدی و تغییر شکلپذیر و پنج قطعه صلب بوده که سه پارت صلب در نقش تکیه ...

ادامه نوشته »

Simulation flexural response of aluminium alloy profile in Abaqus- Damage investigation

In this tutorial, the Simulation flexural response of aluminum alloy profile in Abaqus- Damage investigation- has been studied. Aluminum alloys are used across a range of structural engineering applications, with square and rectangular hollow sections being a popular cross-section shape. This can be particularly beneficial for enhancing resistance to local ...

ادامه نوشته »

شبیه سازی تست خمش دینامیکی پروفیل آلمینیومی در نرم افزار آباکوس-بررسی پارامتر آسیب

در این ویدئو آموزشی به شبیه سازی تست خمش دینامیکی پروفیل آلمینیومی در نرم افزار آباکوس-بررسی پارامتر آسیب- پرداخته ایم. مدل سازی به صورت سه بعدی بوده و پروفیل آلمینیومی به صورت یک پارت شل سه بعدی و اجسام صلب در نقش جسم وارد کننده نیرو و همچنین تکیه گاه ...

ادامه نوشته »

شبیه سازی انفجار به روش کوپل اویلری-لاگرانژی در نزدیکی یک پنل شیشه ای در آباکوس

در این ویدئوی آموزشی به شبیه سازی انفجار به روش کوپل اویلری-لاگرانژی در نزدیکی یک پنل شیشه ای در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده که در آن پارت شیشه،تی ان تی و هوا به صورت سه بعدی طراحی شده اند. فضای اویلری نیز به ...

ادامه نوشته »

Simulation Bending behavior of aluminum foam-filled double cylindrical tubes in Abaqus

In this tutorial, Simulation Bending behavior of aluminum foam-filled double cylindrical tubes in Abaqus has been studied. During the past two decades, many research works have been done to study the axial crushing behavior of thin-walled columns, which work as energy absorption members, in order to improve their capacity. On ...

ادامه نوشته »

finite element analysis of smooth particle hydrodynamics for application to projectile impact on cementitious material

In this tutorial, finite element analysis of smooth particle hydrodynamics for application to projectile impact on cementitious material has been investigated. The performance of brittle, cementitious armor panels under high-rate impact is dependent on a wide range of variables including but not limited to projectile and target geometry, impact velocity, ...

ادامه نوشته »

Flexural Behavior of Concrete Filled Square Steel Tube with Inner CFRP Circular Tube in Abaqus

In this tutorial, Flexural Behavior of Concrete Filled Square Steel Tube with Inner CFRP Circular Tube in Abaqus has been studied. Owing to the development of concrete technology and the demand of practical engineering, high strength concrete has been widely used in construction. The weakness of high strength concrete is ...

ادامه نوشته »

شبیه سازی تست خمش سه نقطه ای قوطی فولادی پر شده با بتن به همراه لوله میانی کامپوزیتی CFRP در آباکوس

در این ویدئوی آموزشی به شبیه سازی تست خمش سه نقطه ای قوطی فولادی پر شده با بتن به همراه لوله میانی کامپوزیتی CFRP در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و قوطی فولادی بیرونی به همراه لوله کامپوزیتی داخلی با استفاه از پارت شل، ...

ادامه نوشته »

Simulation cyclic loading over steel beam column with steel angle and gusset in Abaqus

In this tutorial, Simulation cyclic loading over steel beam-column with steel angle and gusset in Abaqus has been investigated. The steel beam and box column are modeled as a three-dimensional shell part. The steel angle and gusset are modeled as a three-dimensional solid part. You can see a figure of ...

ادامه نوشته »

شبیه سازی بارگذاری تکراری روی یک تیر فولادی متصل به ستون به همراه نبشی و لچکی در نرم افزار آباکوس

در این ویدئو آموزشی به شبیه سازی بارگذاری تکراری روی یک تیر فولادی متصل به ستون به همراه نبشی و لچکی در نرم افزار آباکوس پرداخته ایم. تیر فولادی و ستون قوطی شکل با استفاده از مدل شل سه بعدی و نبشی به همراه لچکی به عنوان تقویت کننده به ...

ادامه نوشته »

Simulation ballistic impact on ceramic titanium composite armor in Abaqus

In this tutorial, the Simulation ballistic impact on the ceramic-titanium-composite armor in Abaqus has been studied. The ceramic, titanium and composite layers are modeled as a three-dimensional solid part. The bullet is modeled as a three-dimensional solid part. You can see a figure of the assembled parts at below The ...

ادامه نوشته »

شبیه سازی برخورد سرعت بالای جسم صلب به صفحه چندلایه سرامیک-تیتانیوم-کامپوزیت در آباکوس

در این ویدئوی آموزشی به شبیه سازی برخورد سرعت بالای جسم صلب به صفحه چندلایه سرامیک-تیتانیوم-کامپوزیت در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و مجموعه شامل صفحه سرامیکی محافظ رویی، صفحه تیتانیومی میانی و دو صفحه دولایه کامپوزیتی اپوکسی شیشه در پشت می باشد. گلوله ...

ادامه نوشته »

شبیه سازی تست خمش سه نقطه ای تیر فولادی قوطی شکل دو پوسته ای پر شده با بتن در آباکوس

در این ویدئوی آموزشی به شبیه سازی تست خمش سه نقطه ای تیر فولادی قوطی شکل دو پوسته ای پر شده با بتن در نرم افزار آباکوس پرداخته ایم. پوسته قوطی شکل فولادی بیرونی و داخلی به صورت پارت شل سه بعدی ترسیم شده اند. مقطع بتنی داخلی یا هسته ...

ادامه نوشته »

Simulation Behavior of thin-walled dodecagonal section double skin concrete-filled steel tubular beam-columns in Abaqus

In this tutorial, Simulation Behavior of thin-walled dodecagonal section double skin concrete-filled steel tubular beam-columns in Abaqus had been studied. The steel sections are modeled as a three-dimensional shell part and the concrete is modeled as a three-dimensional solid part. You can see a figure of the assembled parts at ...

ادامه نوشته »

Simulation Crashworthiness behavior of aluminum profiles with holes considering damage criteria and damage evolution

In this tutorial, Simulation Crashworthiness behavior of aluminum profiles with holes considering damage criteria and damage evolution has been studied. Recently, the use of thin-walled structures in automobiles to increase the safety and integrity of passengers during car collisions, have gained importance by automotive manufacturers and designers. An important characteristic ...

ادامه نوشته »

Simulation CEL explosion over the composite foam-insulated concrete sandwich panels in Abaqus

In this tutorial, the Simulation CEL explosion over the composite foam-insulated concrete sandwich panels in Abaqus has been studied. Two concrete layers at the front and back are modeled as a three-dimensional solid part. The foam inside those two layers is modeled as a three-dimensional part and the beam as ...

ادامه نوشته »

شبیه سازی انفجار به روش کوپل اویلری-لاگرانژی روی یک پنل بتنی سه لایه با هسته فومی در آباکوس

در این ویدئو به شبیه سازی انفجار به روش کوپل اویلری-لاگرانژی روی یک پنل بتنی سه لایه با هسته فومی در نرم افزار آباکوس پرداخته ایم. مدل شامل دو قطعه بتنی سه بعدی و سالید به همراه یک قطعه فومی در میانه آنها می باشد. در هر دو قطعه بتنی ...

ادامه نوشته »

Numerical simulation of blast resistance of RC slab strengthened with AFRP in Abaqus-Damage investigation

In this tutorial, numerical simulation of blast resistance of RC slab strengthened with AFRP in Abaqus-Damage investigation- has been studied. The concrete slab is modeled as a three-dimensional solid part, the AFRP is modeled as four layers composite with shell part and the embedded beam inside the concrete host is ...

ادامه نوشته »

شبیه سازی انفجار در هوا روی یک قطعه بتنی تقویت شده با الیاف AFRP در نرم افزار آباکوس- بررسی آسیب

در این ویدئو به شبیه سازی انفجار در هوا روی یک قطعه بتنی تقویت شده با الیاف AFRP در نرم افزار آباکوس- بررسی آسیب- پرداخته ایم. مدل بتن به صورت سه بعدی و سالید، میلگردها به صورت پارت وایر سه بعدی و ورق کامپوزیتی از جنس الیاف آرامید به صورت ...

ادامه نوشته »

Simulation cyclic loading of the reduce beam section-column with stiffener in Abaqus

In this tutorial, Simulation cyclic loading of the reduce beam section-column with a stiffener in Abaqus has been investigated. The RBS part is modeled as a three-dimensional shell part, the box column, and the stiffener is modeled as three-dimensional shell parts. You can see a figure of the assembled parts ...

ادامه نوشته »

Simulation composite column (steel beam and concrete) under cyclic loading in Abaqus

In this tutorial, the simulation composite column(steel beam and concrete)under cyclic loading in Abaqus has been studied. The steel beam and the concrete parts are modeled as three-dimensional solid parts. You can see a figure of the assembled parts at below The steel material is used for the steel beam ...

ادامه نوشته »

Simulation High velocity impact of a brass projectile on the Ceramic-Aluminum-Glass fiber in Abaqus

In this tutorial, Simulation High-velocity impact of a brass projectile on the Ceramic-Aluminum-Glass fiber in Abaqus has been investigated. The brass projectile, the ceramic plate, aluminum plate, and epoxy-glass layers are modeled as three-dimensional parts. You can see a figure of the assembled parts at below The brass material is ...

ادامه نوشته »

شبیه سازی برخورد پرتابه سرعت بالای برنجی به ورق چندلایه سرامیکی-آلمینیومی-کامپوزیتی در نرم افزار آباکوس

در این ویدئو آموزشی به شبیه سازی برخورد پرتابه سرعت بالای برنجی به ورق چندلایه سرامیکی-آلمینیومی-کامپوزیتی در نرم افزار آباکوس پرداخته ایم. تمامی اجزا شامل پرتابه،ورق سرامیکی،ورق آلمینیومی و چهار لایه کامپوزیت به صورت سه بعدی و تغییر شکلپذیر ترسیم شده اند. در شکل زیر می توانید نحوه قرارگیری اجزا ...

ادامه نوشته »

Simulation steel beam-column connection with bolt in Abaqus-Beam failure investigation

In this tutorial, the Simulation steel beam-column connection with bolt-in Abaqus under vertical load-Beam failure investigation- has been studied. The beam with endplate is modeled as a three-dimensional solid part, the column is modeled as a three-dimensional solid part and the ten bolts are modeled as three-dimensional solid parts. You ...

ادامه نوشته »

شبیه سازی اتصال تیر به ستون فولادی با پیچ و بررسی پارگی ورق تیر تحت اثر جابه جایی عمودی در آباکوس

در این ویدئو به شبیه سازی اتصال تیر به ستون فولادی با پیچ و بررسی پارگی ورق تیر تحت اثر جابه جایی عمودی در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و تیر به همراه ورق انتهایی جوش شده به صورت سه بعدی و سالید، مجموعا ...

ادامه نوشته »

Simulation steel beam-column connection with steel angle under cyclic loading in Abaqus

In this tutorial Simulation steel beam-column connection with steel angle under cyclic loading in Abaqus has been investigated. The beam and column are modeled as three-dimensional shell parts and the steel angle is modeled as a three-dimensional shell part. You can see a figure of the assembled parts at below ...

ادامه نوشته »

شبیه سازی اتصال پیچی تیر به ستون و بررسی پارگی پیچ ها تحت بار عمودی در نرم افزار آباکوس

در این ویدئو به شبیه سازی اتصال پیچی تیر به ستون و بررسی پارگی پیچ ها تحت بار عمودی در نرم افزار آباکوس پرداخته ایم. مدل شامل سه پارت سه بعدی تغییر شکل پذیر تیر فولادی،ستون و مجموعا ده پیچ می باشد که در شکل زیر می توانید نحوه قرارگیری ...

ادامه نوشته »

Simulation cyclic loading over a steel column with stiffeners in Abaqus-Damage investigation

In this tutorial, Simulation cyclic loading over a steel column with stiffeners in Abaqus-Damage investigation- has been studied. The box column is modeled as a three-dimensional shell part and the stiffener is modeled as a planar shell part. You can see a figure of assembled part at below The stiffeners ...

ادامه نوشته »

Simulation reinforced concrete beam with FRP under four points bending in Abaqus

In this tutorial, Simulation reinforced concrete beam with FRP under four points bending in Abaqus has been studied. The concrete beam is modeled as three dimensional part, the FRP is modeled as a conventional shell with tow layouts with different rotation angle. You can see a figure of the assembled ...

ادامه نوشته »

Simulation underwater explosion near a concrete dam by using the CEL method in Abaqus

In this tutorial Simulation underwater explosion near a concrete dam by using the CEL method in Abaqus has been investigated. The dam is modeled as a three dimensional part, The TNT, water, and air are modeled as the Eulerian part. You can see a figure of the assembled parts at ...

ادامه نوشته »

شبیه سازی انفجار به روش اویلری لاگرانژی در نزدیکی یک سد بتنی در آباکوس-انفجار زیر آب

در این ویدئو به شبیه سازی انفجار به روش اویلری لاگرانژی در نزدیکی یک سد بتنی در آباکوس-انفجار زیر آب- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و سد به صورت جسم تغییر شکلپذیر ترسیم شده است. ماده منفجره،هوا و آب نیز به صورت پارت اویلری سه بعدی ایجاد ...

ادامه نوشته »

Simulation steel pipe reinforcement with CFRP layouts in Abaqus under three points bending

In this tutorial Simulation steel pipe reinforcement with CFRP layouts in Abaqus under three points bending has been studied. Circular hollow section (CHS) are widely used in many applications but predominantly used as pipelines in the oil and gas industry. Natural resources like oil and gas constitute the major share ...

ادامه نوشته »

Masonry wall behavior under couple Eulerian-Lagrangian explosion in Abaqus

In this tutorial Masonry wall behavior under couple Eulerian-Lagrangian explosion in Abaqus has been simulated.Numerical simulations are used extensively for solving a vast variety of dynamic problems associated with explosions, such as gaseous or condensed charge detonations followed by pressure wave propagation through the ambient air. Utilizing these methods, it ...

ادامه نوشته »
تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
enemad-logo