بایگانی برچسب: abaqus

In this tutorial, the Simulation compression test of the concrete column with and without steel reinforcement-Compression test- has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts and two rigid bodies as boundary zone and hydraulic jack. You can ...

در این ویدئوی آموزشی به شبیه سازی تست فشار ستون کوتاه بتنی با و بدون تقویت کننده فلزی در آباکوس-مقایسه باربری- پرادخته ایم. مدلسازی به صورت سه بعدی شامل هندسه ستون بتنی، میلگرد ها و اجسام صلب در نقش تکیه گاه و جسم وارد کننده نیرو می باشد. ستون بتنی ...

In this tutorial, the Simulation RC column retrofitted with CFRP and epoxy under compression load in Abaqus has been done. The circular concrete column is modeled as a three-dimensional solid part. The sell strips and bars are modeled as three-dimensional wire parts. The CFRP is modeled as a conventional shell ...

In this tutorial, the Thermal and Structural Analysis of Exhaust Manifold in Abaqus has been investigated. The manifold geometry is a complex one, so the geometry is imported to the Abaqus from SolidWorks software. You can see a figure of the manifold part below The exhaust manifold is a very ...

In this tutorial, the damage and failure investigation of the CFRP composite military helmet under close blast explosion has been studied. The military helmet is a 3D shell part with eight different layers. The helmet part is imported to the Abaqus because of the part complexity. You can see a ...

In this tutorial, the Seismic behavior of RC exterior wide beam-column joints in Abaqus has been simulated. The concrete beam and column are modeled as three-dimensional solid parts. The steel bars and strips are modeled as three-dimensional wire parts. You can see a figure of the assembled parts below Reinforced ...

In this tutorial, the High-velocity impact of a bullet on the RC panel- Paper validation- is investigated. The dimensions are extracted from the paper. The concrete slab is modeled as a three-dimensional solid part. The steel reinforcements are modeled as three-dimensional wire parts. The bullet is modeled as a discrete ...

In this course, you will learn all aspects of steel structure modeling and simulation in Abaqus. The lecture contains sixteen sections, in each section, the tutor has explained all thing from A to Z. Geomert modeling, material definition and equations, steps, interaction, load, mesh, and results. The dynamic bolt failure, ...

In this full lecture, all aspects of soil modeling and simulation are represented. The lecture contains twenty titles about soil, saturated soil, TBM, earthquake, tunnel, embankment construction, geocell reinforced soil, geosynthetic-reinforced soil retaining wall, earthquake over a concrete tunnel, embankment, and excavation, soil consolidation in interaction with the concrete pile, ...

In this lecture, the High and Low-velocity impact phenomenon is investigated. The lecture duration is more than ten hours and during that, twenty different models are simulated based on the research paper as a reference for the material. We define the proper material model for each part for instance in ...

In this lecture through Twenty step by step tutorial, many aspects of the concrete structure like a beam, RC beam and column, normal concrete, UHPC, and UHPFRC concrete, composite beam, and column, cyclic loading over the RC beam and column, CFDST and CFST column, ECC beam-column joint, high strength concrete ...

In this lecture, we explained twelve titles about Bio-Mechanical engineering. During the lecture, we explained each model from A to Z. First, schematic of the problem and then modeling and simulation In the first lecture, the pull-out process of the medical screws from the bone has been investigated. The material ...

In this course, we explained the Coupled Eulerian-Lagrangian, Smooth Particle Hydrodynamic, Acoustic, and CONWEP blast procedure in detail during twenty-three separate tutorials which you can see their title below. We provide this course because some people use our tutorials to create courses on Udemy but if you ask them questions ...

In this tutorial, the Simulation cyclic loading of a composite Column(UHPC + Steel box) in Abaqus has been studied. The Ultra-High-Performance Concrete column is modeled as a three-dimensional solid part. The steel box cover is modeled as a three-dimensional shell part. You can see a figure of the assembled parts ...

In this tutorial, the Simulation oblique high-velocity impact of an aluminum rod to the silicon-carbide target in Abaqus has been investigated. The silicon-carbide target is modeled as a three-dimensional solid part. The aluminum projectile is modeled as a three-dimensional solid part. You can see a figure of the assembled parts ...

In this tutorial, the Simulation cyclic loading behavior of a reinforced rubberized concrete column in Abaqus has been investigated. The rubberized concrete column is modeled as a three-dimensional solid part. The steel bars and strips are modeled as three-dimensional wire part. You can see a figure of the assembled parts ...

In this tutorial, the Simulation of low energy impact on the RC beam and residual displacement investigation in Abaqus has been done. The concrete beam is modeled as a three-dimensional solid part. The steel bars and strips are modeled as three-dimensional wire parts. The hammer is modeled as a rigid ...

در این مثال آموزشی به شبیه سازی تیر بتنی مسلح تحت اثر ضربه کم انرژی در نرم افزار آباکوس-بررسی جابه جایی پسماند- در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل تیر بتنی به صورت سالید، میلگردهای طولی و خاموت ها به صورت سه بعدی ...

In this tutorial, the Simulation of rigid body impact on the interior voided RC slab in Abaqus has been investigated. The RC voided slab is modeled as a three-dimensional solid part. The steel bars are modeled as three-dimensional wire parts. The rigid impactor is modeled as a three-dimensional shell part. ...

In this tutorial, the Simulation dynamic bending of RC beams strengthened with CFRP rods and Epoxy glue in Abaqus has been done. The concrete beam is modeled as a three-dimensional solid part. The CFRP rod and epoxy glue are modeled as three-dimensional solid parts. The steel bars and strips are ...

در این ویدئوی آموزشی به شبیه سازی خمش دینامیکی تیر بتنی مسلح به میلگرد فولادی،چسب اپوکسی و میلگردCFRP در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل پارت تیر بتنی به صورت سالید و سه بعدی، پارت میلگرد CFRP به صورت سالید و سه بعدی، پارت چسب به صورت سالید و ...

In this tutorial, the Simulation blast explosion over the composite panel(Steel-Aluminum-Ceramic-CFRP) in Abaqus has been investigated. The steel and aluminum plates are modeled as three-dimensional solid part. The silicon carbide or ceramic is modeled as a three-dimensional solid part. The CFRP is modeled as a three-dimensional solid part with four ...

در این ویدئوی آموزشی به شبیه سازی انفجار روی یک پنل مرکب(فولاد-آلمینیوم-سرامیک-CFRP) در نرم افزار آباکوس پرداخته ایم. مدلسازی به صرت سه بعدی بوده و ورق رویی فولادی و آلمینیومی به صورت سالید و تغییر شکلپذیر طراحی شده اند. لایه ضخیم سرامیکی و لایه زیرین CFRP چهار لایه نیز به ...

In this tutorial, the Simulation dynamic bending test of an interior voided RC UHPC beam in Abaqus has been studied. The Ultra-High-Performance Concrete beam is modeled as three-dimensional solid part with interior sphere voids. The steel bar and strips are modeled as three-dimensional wire parts. The rigid bodies are used ...

In this tutorial, the Simulation ship moving through Ice-Water path in Abaqus by using SPH method has been done. The ship is imported to the Abaqus because of its complex geometry. The ice and water are modeled as a three-dimensional solid part. You can see a figure of the assembled ...

In this tutorial, the Simulation air blast load over a composite beam( UHPFRC- Steel beam with Shear stud) in Abaqus has been investigated. The Ultra-High-Performance-Fiber-Reinforced Concrete is modeled as a three-dimensional solid part. The stud is modeled as a three-dimensional solid part. The steel beam is modeled as a three-dimensional ...

در این ویدئوی آموزشی به شبیه سازی انفجار روی یک تیر کامپوزیت( بتن فوق توانمند الیافی-تیر فولادی-گلمیخ) در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل پارت بتن فوق توانمند الیافی به صورت سالید و سه بعدی، پارت تیر فولادی به صورت شل و سه بعدی و در نهایت گلمیخ ها ...

In this tutorial, the Simulation air blast explosion over campsite slab(UHPC-Steel) by using cohesive interaction in Abaqus  has been done. The two steel covers are modeled as three-dimensional solid part. The Ultra-High-Performance concrete is modeled as a three-dimensional solid par. You can see a figure of the assembled parts below ...

In this tutorial, the Simulation low velocity impact on the CFRP-AL Foam-CFRP panel in Abaqus has been investigated. The CFRP are modeled as three-dimensional solid parts with four different fiber direction. The Aluminum-Foam as a core part is modeled as a three-dimensional solid part. The projectile is modeled as the ...

In this tutorial, the Simulation bending test of a steel-concrete(foamed concrete) composite beam in Abaqus  has been studied. The foamed concrete ( containing partial cement replacement) is modeled as a three-dimensional solid part. The steel beam is modeled as a three-dimensional shell part. The steel reinforcement is modeled as a ...

در این ویدئوی آموزشی به شبیه سازی خمش تیر کامپوزیتی فولادی-بتنی( ذرات خاکستر جایگزین جزئی سیمان) در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل دال بتنی ساخته شده از مخلوط بتن با خاکستر و پوسته تخم مرغ به صورت سه بعدی و سالید، تیر ...

In this tutorial, the Simulation air blast explosion over a Wood-Concrete slab reinforced with BFRP lamina in Abaqus  has been investigated. The wood-concrete part is modeled as a three-dimensional solid part. The Basalt Fiber Reinforced Plastic( BFRP) is model as a shell part with eight layers. The steel reinforcement which ...

در این ویدئوی آموزشی به شبیه سازی انفجار در هوا روی یک دال کامپوزیتی چوبی-سیمانی تقویت شده با الیاف بازالت در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل یک پارت بتنی کامپوزیتی ساخته شده از ترکیب چوب-سیمان به صورت سه بعدی و سالید، پارت ...

In this tutorial, the Simulation bending test of the UHPFRC beam reinforced with BFRP lamina in Abaqus  has been investigated. The UHPFRC beam is modeled as a three-dimensional solid part. The BFRP lamina with eight layers is modeled as a shell part. The steel bars and strips are modeled as ...

In this tutorial, the Simulation air blast explosion over the RC beam reinforce with Banana-Epoxy lamina in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The bar and strip are modeled as three-dimensional wire part. The Banana-Epoxy part is modeled as a three-dimensional shell ...

در این ویدئوی آموزشی به شبیه سازی انفجار در هوا روی یک تیر بتنی تقویت شده با میلگرد و الیاف گیاهی در نرم افزار آباکوس-بررسی تخریب- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و تیر بتنی به صورت یک پارت سالید و سه بعدی، میلگردها و خاموت ها به ...

In this tutorial, the Simulation steel beam under fire and mechanical load condition in Abaqus  has been investigated. The steel beam is modeled as a three-dimensional solid part and also it can be modeled as a shell part. You can see a figure of the part with fire and mechanical ...

در این ویدئوی آموزشی به شبیه سازی فرآیند آتش سوزی روی یک تیر فولادی به همراه بارگذاری مکانیکی در نرم افزار آباکوس- بررسی تبدیل حرارت به تنش- پرداخته ایم. مدل سازی به صورت سه بعدی بوده و تیر فولادی به صورت یک پارت سالید طراحی شده است. در این آنالیز ...

In this tutorial, the Simulation compression test of the short concrete column reinforce with Banana-Epoxy lamina in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The Banana-Epoxy lamina is modeled as a three-dimensional shell part. The steel bars and strips are modeled as three-dimensional ...

در این ویدئوی آموزشی به شبیه سازی تست فشار ستون کوتاه بتنی تقویت شده با میلگرد و الیاف گیاهی در نرم افزار آباکوس پرداخته ایم. مدل سازی شامل یک ستون کوتاه بتنی به صورت سه بعدی و سالید، میلگردهای طولی و خاموت ها به صورت سیمی و سه بعدی، الیاف ...

In this tutorial, the Simulation high-velocity impact of the steel rod to the composite panel(Steel-Ceramic-AFRP) in Abaqus  has been done. The steel rod and steel cover are modeled as three-dimensional solid part. The ceramic part is modeled as a three-dimensional solid part. The Aramid Fiber Reinforced Plastic(AFRP) is modeled as ...

در این ویدئوی آموزشی به شبیه سازی برخورد میله فولادی به پنل مرکب( فولاد-سرامیک-الیاف آرامید) و بررسی آسیب آن در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل پارت سه بعدی و سالید میله ضربه زننده، پارت سه بعدی ورق فولادی در نقش لایه محافظ، لایه میانی به صورت سالید و ...

In this tutorial, the Simulation four-point bending of a concrete beam reinforced with steel bar and BFRP in Abaqus  has been done. The concrete beam is modeled as a three-dimensional solid part. The Basalt Fiber reinforced Plastic(BFRP) is modeled as a shell part with four layers. The strips and bars ...

در این ویدئوی آموزشی به شبیه سازی خمش چهار محوره تیر بتنی تقویت شده با میلگرد و کامپوزیت بازالت چند لایه در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و تیر بتنی به صورت سالید، میلگرد و خاموت ها به صورت سیمی یا وایر، کامپوزیت بازالت ...

In this tutorial, the Simulation air blast explosion over the UHPC slab reinforced with BFRP composite in Abaqus has been investigated. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. The Basalt fiber reinforced plastic(BFRP) is modeled as a shell part with four layers. You can see a figure of ...

در این ویدئوی آموزشی به شبیه سازی انفجار در هوا روی یک دال بتنی فوق توانمند تقویت شده با الیاف بازالت در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و پارت بتنی فوق توانمند به صورت سالید و پارت کامپوزیت بازالت به صورت شل ترسیم شده ...

In this tutorial, the Simulation retrofit Jute-Epoxy composite of the concrete column under dynamic compression in Abaqus  has been investigated. The concrete column is modeled as a three-dimensional solid part. The just-Epoxy part is modeled as a three-dimensional shell. A rigid body is used as the hydraulic jack. You can ...

در این ویدئوی آموزشی به شبیه سازی تست فشار دینامیکی ستون بتنی تقویت شده با الیاف کامپوزیت Jute-Epoxy در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل پارت ستون بتنی به صورت سالید، پارت کامپوزیتی Jute-Epoxy به صورت شل و در نهایت یک پارت صلب ...

In this tutorial, the Simulation three-point bending test of the UHPC beam reinforced with Jute-Epoxy lamina in Abaqus has been investigated. The UHPC beam is modeled as a three-dimensional solid part. The Jute-Epoxy lamina is modeled as a three-dimensional shell part with four layers. A rigid body shell part is ...

در این ویدئوی آموزشی به شبیه سازی خمش سه محوره تیر بتنی فوق توانمند تقویت شده با الیاف Jute-Epoxy در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل قطعه بتنی فوق توانمند به صورت سه بعدی و سالید، قطعه کامپوزیتی به صورت شل و صفحه ای، و قطعه صلب در نقش ...