تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
خانه / بایگانی برچسب: abaqus damage simulation

بایگانی برچسب: abaqus damage simulation

Simulation of cyclic loading of a steel beam reinforced with epoxy and CFRP in Abaqus

In this tutorial, the Simulation of cyclic loading of a steel beam reinforced with epoxy and CFRP in Abaqus has been done. The steel beam is modeled as a three-dimensional shell part. The epoxy and CFRP are modeled as three-dimensional solid parts. You can see a figure of the assembled ...

ادامه نوشته »

Simulation Pull-Out test of a ribbed steel bar from the UHPC part in Abaqus

In this tutorial, the Simulation Pull-Out test of a ribbed steel bar from the UHPC part in Abaqus has been investigated. The steel bar is imported to Abaqus from the CAD software because of the complex geometry as a solid part. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. ...

ادامه نوشته »

Damage and crack identification in concrete by using piezoelectric material in Abaqus

In this tutorial, the Damage and crack identification in concrete by using piezoelectric material in Abaqus has been simulated. The concrete part with the initial crack is modeled as a three-dimensional solid part. The PZT parts are modeled as three-dimensional solid parts. You can see a figure of the assembled ...

ادامه نوشته »

Simulation air blast load over a composite beam(Wood+Aluminum) in Abaqus

In this example, the Simulation air blast load over a composite beam(Wood+Aluminum) in Abaqus has been investigated. The wood slab is modeled as a  three-dimensional solid part with tension and compression zones. The aluminum beam is modeled as a three-dimensional shell part. You can see a figure of the assembled ...

ادامه نوشته »

Simulation wood timber beam under fire and mechanical bending load in Abaqus

In this tutorial, the Simulation wood timber beam under fire and mechanical bending load in Abaqus has been done. The timber beam is modeled as a three-dimensional solid part. You can see a figure of the assembled parts below Along with the innovation of new building systems, how we design ...

ادامه نوشته »

Simulation wood-steel plate connection with nail under tension load in Abaqus

In this tutorial, the Simulation wood-steel plate connection with a nail under tension load in Abaqus has been investigated. The steel plate and nail are modeled as three-dimensional solid parts. The wooden plate also is a three-dimensional part. You can see a figure of the assembled parts below Cross-laminated timber ...

ادامه نوشته »

Simulation bending test of an aluminium-timber composite beam with connections in Abaqus

In this project, the Simulation bending test of an aluminium-timber composite beam with connections in Abaqus has been done. The timber wood slab is modeled as a three-dimensional solid part. The aluminium beam is modeled as a three-dimensional shell part. You can see a figure of the assembled parts below ...

ادامه نوشته »

Simulation air blast load over a reinforced concrete beam with spiral GFRP bar in Abaqus

In this tutorial, the Simulation air blast load over a reinforced concrete beam with a spiral GFRP bar in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part, the spiral GFRP is a solid part also. The steel reinforcements are modeled as three-dimensional wire parts. ...

ادامه نوشته »

Simulation compression test of a concrete column reinforced with GFRP bars and strips in Abaqus

In this tutorial, the Simulation compression test of a concrete column reinforced with GFRP bars and strips in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The GFRP bars and strips are modeled as three-dimensional solid parts. You can see a figure of the ...

ادامه نوشته »

Fire simulation in Abaqus-Thermal and Structural analysis of a steel frame

In this tutorial, the Fire simulation in Abaqus-Thermal and Structural analysis of a steel frame has been investigated. The steel beam is modeled as an I-shape three-dimensional part. The two box columns are modeled as three-dimensional parts. You can see a figure of the assembled parts below Steel has been ...

ادامه نوشته »

Investigation on the repeated impact responses of circular concrete-filled double-tube (CFDT) members in Abaqus

In this tutorial, the Investigation on the repeated impact responses of circular concrete-filled double-tube (CFDT) members in Abaqus have been studied. The two concrete cores are modeled as three-dimensional solid parts. The two steel tubes are modeled as three-dimensional solid parts. The rigid hammer as an impact is used also. ...

ادامه نوشته »

Simulation air blast explosion over a composite panel(Silica glass-Aluminum-CFRP) in Abaqus

In this tutorial, the Simulation air blast explosion over a composite panel(Silica glass-Aluminum-CFRP) in Abaqus has been investigated. The silica glass is modeled as a three-dimensional part. The aluminum as the middle layer is modeled as a three-dimensional solid part. The CFRP as the backplate is modeled as a shell ...

ادامه نوشته »

Simulation cyclic loading of a steel beam-column joint filled with the UHPC and welded stiffeners in Abaqus

In this tutorial, the Simulation cyclic loading of a steel beam-column joint filled with the UHPC and welded stiffeners in Abaqus has been done. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. The steel beam and column are modeled as three-dimensional shell parts. The stiffeners are modeled as three-dimensional ...

ادامه نوشته »

Simulation of a steel bullet impact on the composite panel(Boron carbide-CFRP-Gelatin) in Abaqus

In this tutorial, the Simulation of a steel bullet impact on the composite panel (Boron carbide-CFRP-Gelatin) in Abaqus has been investigated. The bullet is modeled as a three-dimensional solid part. The boron carbide and gelatin are modeled as three-dimensional solid parts. The CFRP is modeled as a shell with eight ...

ادامه نوشته »

Finite element analysis of progressive collapse of reinforced ,Ultra-High-Performance-Concrete frame

In this tutorial, the Finite element analysis of the progressive collapse of reinforced, Ultra-High-Performance-Concrete frame has been investigated. The UHPC frame is modeled as a three-dimensional solid part. The steel reinforcements are modeled as three-dimensional wire parts. You can see a figure of the assembled parts below Progressive collapse is ...

ادامه نوشته »

Simulation of a CEL large-scale bomb explosion(Nuclear detonation) near a building in Abaqus

In this tutorial, the Simulation of a CEL large-scale bomb explosion (Nuclear detonation) near a building in Abaqus has been investigated. A nuclear explosion releases vast amounts of energy in the form of blasts, heat, and radiation. An enormous Shockwave reaches speeds of many hundreds of kilometers an hour. The blast ...

ادامه نوشته »

Simulation compression test of a composite column(wood-uhpc-steel cover) in Abaqus

In this tutorial, the Simulation compression test of a composite column(wood-uhpc-steel cover) in Abaqus has been investigated. The wood core and Ulta-High-Performance-Concrete parts are modeled as three-dimensional solid parts. The steel cover is modeled as a shell part. You can see a figure of the assembled parts below Wood columns ...

ادامه نوشته »

Simulation Phantom aircraft collision on a concrete wall in Abaqus

In this tutorial, the Simulation Phantom aircraft collision with a concrete wall in Abaqus has been investigated. The concrete wall is modeled as a three-dimensional solid part. The Phantom is imported as an input geometry to Abaqus as a shell part. You can see a figure of the parts below ...

ادامه نوشته »

Simulation air blast analysis of a composite column(wood-concrete-CFRP) in Abaqus

In this tutorial, the Simulation air blast analysis of a composite column(wood-concrete-CFRP) in Abaqus has been investigated. The wood is modeled as a three-dimensional solid part with two layers of tension and compression. The concrete is modeled as a three-dimensional solid part. The steel bars and strips are modeled as ...

ادامه نوشته »

Simulation bending test of a composite beam(wood-UHPC-Steel) in Abaqus

In this tutorial, the Simulation bending test of a composite beam(wood-UHPC-Steel) in Abaqus has been done. The wood is modeled as a three-dimensional solid part with two layers, the top layer is in compression, and the bottom is in tension. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. The ...

ادامه نوشته »

Simulation under water explosion by using CEL method near a floating structure in Abaqus

 In this tutorial, the Simulation under-water explosion by using the CEL method near a floating structure in Abaqus has been investigated. The aluminum hull is modeled as a three-dimensional thick shell part. The Soil, TNT, Water, and Air are modeled as three-dimensional parts inside the Eulerian domain. You can see ...

ادامه نوشته »

Simulation CEL explosion near a stone wall covered with cloth concrete in Abaqus

In this tutorial, the  Simulation CEL explosion near a stone wall covered with cloth, and concrete in Abaqus has been investigated. The stone wall and cloth, concrete are modeled as three-dimensional solid parts. The TNT is a solid sphere, and the Eulerian domain is a 3D body. You can see ...

ادامه نوشته »

Simulation of RC Beams during Fire Events Using a Fully Coupled Thermal-Stress Analysis in Abaqus

In this tutorial, the Simulation of RC Beams during Fire Events Using a Fully Coupled thermal stress Analysis in Abaqus has been studied. The concrete beam is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts. You can see a figure of the assembled parts ...

ادامه نوشته »

Simulation of Push-Out test on a new shear connector of I-Shape in Abaqus

In this tutorial, the Simulation of the Push-Out test on a new shear connector of the I-Shape in Abaqus has been investigated. The concrete is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts. The steel beam and connector are modeled as three-dimensional solid part. ...

ادامه نوشته »

Simulation air blast load over a RC beam reinforced with Cloth Concrete cover in Abaqus

In this tutorial, the Simulation air blast load over a RC beam reinforced with Cloth Concrete cover in Abaqus has been done, The normal concrete core is modeled as a three-dimensional solid part. The cloth concrete part is modeled as a three-dimensional patrt. The steel bar and strips are modeled ...

ادامه نوشته »

Simulation full three Dimensional fire analysis of a Reinforced concrete beam in Abaqus-Sequential Coupling Technique

In this tutorial, the Simulation full three Dimensional fire analysis of a Reinforced concrete beam in Abaqus-Sequential Coupling Technique- has been investigated. The concrete beam is modeled as a three-dimensional solid part,. The longitudal bar and strips are modeled as three-dimensional solid part. You can see a figure of the ...

ادامه نوشته »

Simulation CEL explosion inside the RC UHPC building in Abaqus-Damage investigation

In this tutorial, the Simulation CEL explosion inside the RC UHPC building in Abaqus-Damage investigation has been done The Ulta-High-Performance-Concrete(UPHC) building is modeled as a three-dimensional solid part. The reinforcements are modeled as wire part. The TNT is shpere part inside the Eulerian domain. You can see figures of the ...

ادامه نوشته »

Simulation compression test of a RC column with spiral CFRP with fully damaged behaviour in Abaqus

In this tutorial, the Simulation compression test of a RC column with spiral CFRP with fully damaged behaviour in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The spiral CFRP is modeled as a three-dimensional solid part. The steel bar is modeled as a ...

ادامه نوشته »

Simulation air blast explosion over RC column with spiral strip and steel tube cover in Abaqus

In this tutorial, the Simulation air blast explosion over RC column with spiral strip and steel tube cover in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The spiral strips and bars are modeled as three-dimensional wire part. The steel tube as cover is ...

ادامه نوشته »

Simulation under water explosion shock over a cylindrical aluminum shell in interaction with soil in Abaqus

In this tutorial, the Simulation under water explosion shock over a cylindrical aluminum shell in interaction with soil in Abaqus has been studied. The water is modeled as a three-dimensional solid part with acoustic behaviour. The aluminum part is modeled as a three-dimensional shell part, and the soil as a ...

ادامه نوشته »

Air blast explosion over a rienforced concrete column with spiral CFRP strip in Abaqus

In this tutorial, the Air blast explosion over a rienforced concrete column with spiral CFRP strip in Abaqus has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel strips and bars are modeled as three-dimensional wire part. The spiral CFRP part is modeled as a ...

ادامه نوشته »

Simulation Impact analysis of CFRP/PEEK/ceramic/gelatin composite for finding behind the armor trauma in Abaqus

In this tutorial, the Simulation Impact analysis of CFRP/PEEK/ceramic/gelatin composite for finding behind the armor trauma in Abaqus has been investigated. The CFRP is modeled as a three-dimensional shell part. The polyether-ether-ketone(PEEK) is modeled as a thin solid layer to protect the other layers. The silicon carbide or ceramic is ...

ادامه نوشته »

Simulation CEL explosion of steel-UHPC composite RC beam(column) with multiple encased steel profiles in Abaqus

In this tutorial, the Simulation CEL explosion of steel-UHPC composite RC beam(column) with multiple encased steel profiles in Abaqus  has been done. The Ultra-High-Performance-Concrete is modeled as a three-dimensional solid part. The bar and strip are modeled as three-dimensional wire parts. The steel beam core and TNT part are modeled ...

ادامه نوشته »

شبیه سازی انفجار روی تیر بتنی فوق توانمند با هسته تیر فولادی دوبل به روش اویلری لاگرانژی در آباکوس

در این ویدئوی آموزشی به شبیه سازی انفجار روی تیر بتنی فوق توانمند با هسته تیر فولادی دوبل به روش اویلری لاگرانژی در نرم افزار آباکوس پرداخته ایم. تیر بتنی فوق توانمند به صورت سالید و سه بعدی، تیر های فولادی به صورت سالید و سه بعدی،میلگرد و خاموت ها ...

ادامه نوشته »

Simulation compression test of CFRP composite spirals in circular hollow UHPC columns in Abaqus

In this tutorial, the Simulation compression test of CFRP composite spirals in circular hollow UHPC columns in Abaqus has been done. The Ultra-High-Performace-Concrete column is modeled as a three-dimensional solid part. The spiral CFRP part is modeled as a solid part, the longitudinal steel bar is modeled as a wire ...

ادامه نوشته »

Simulation dynamic bending test of steel-UHPFRC composite beam(column) with multiple encased steel profiles in Abaqus

In this tutorial, the Simulation dynamic bending test of steel-concrete composite beam(column) with multiple encased steel profiles in Abaqus has been done. The beam(column) part is modeled as a three-dimensional solid part, the two steel beam parts are  modeled as three-dimensional solid part. You can see a figure of the ...

ادامه نوشته »

Damage prediction of concrete gravity dams subjected to two underwater explosion shock loading

In this tutorial, the  simulation of Damage prediction of concrete gravity dams subjected to underwater explosion shock loading has been done. The concrete dam is modeled as a three-dimensional solid part. The TNT, water, and air are modeled as eulerian part. The rock foundation is modeled as a three-dimensional solid ...

ادامه نوشته »

Simulation of concrete-encased CFST box stub columns under axial compression in Abaqus

In this tutorial, the Simulation of concrete-encased CFST box stub columns under axial compression in Abaqus has been done. The concrete column is modeled as a three-dimensional solid part. The steel pipes are modeled as three-dimensional solid part also,  and the steel bar and strips are modeled as the wire ...

ادامه نوشته »

Simulation RC beam column joint reinforced with steel plates and rods under vertical load in abaqus

In this tutorial, the Simulation RC beam column joint reinforced with steel plates and rods under vertical load in abaqus  has been investigated. The concrete beam-column is modeled as a three-dimensional solid part. The steel bar and strip are modeled as three-dimensional wire part. The steel plates and rods are ...

ادامه نوشته »

Simulation five point bending of a composite concrete beam(NSC+UHPFRC) in Abaqus

In this tutorial, the Simulation five point bending of a composite concrete beam(NSC+UHPFRC) in Abaqus has been done. The normal strength concrete beam as a cover is modeled as a three-dimensional solid part. The Ultra-High-Performace-Fiber-Reinforce-Concrete core is modeled as the a three-dimensional solid part. The steel bars and strips are ...

ادامه نوشته »

شبیه سازی کشش عمیق ورق فولادی دو لایه با هسته CFRP در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی کشش عمیق ورق فولادی دو لایه با هسته CFRP در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه ورق های فولادی به صورت شل و سه بعدی، پارت ورق CFRP به صورت شل و سه بعدی که چهار لایه بوده، هندسه قالب به ...

ادامه نوشته »

Simulation dynamic compression test of a RC column with UHPFRC core in Abaqus

In this tutorial, the Simulation dynamic compression test of a RC column with UHPFRC core in Abaqus has been done, The concrete column is modeled as a three-dimensional solid part. The steel bar and strip are modeeld as three-dimensional wire paer. The Ultra-High-Performance-Fiber-Reinforce Concrete is modeled as a three-dimensional solid ...

ادامه نوشته »

Simulation air blast over a composite panel( Glass Epoxy-Ceramic-thermoplastic polyurethane) in Abaqus

In this tutorial, the Simulation air blast over a composite panel( Glass Epoxy-Ceramic-thermoplastic polyurethane) in Abaqus has been done. The epoxy glass composite part is modeled as a three-dimensional shell part with sixteen layers. The ceramic and polyurethane are modeled as three-dimensionalsolid part. You can see a figure of the ...

ادامه نوشته »

Simulation dynamic four point bending test of a Gravity beam in Abaqus

In this tutorial, the Simulation dynamic four point bending test of a Gravity beam in Abaqus has been investigated. Gravity Beams, a term coined in this investigation, are those beams in which gravity is used to design the topology of beam form conjointly with the novel manufacturing strategy Fabric Formwork. ...

ادامه نوشته »

Numerical Investigation of Rigid Impact on Steel Wire Reinforced Foam Core/Composite Skin Sandwich Panel

In this tutorial, the Numerical Investigation of Rigid Impact on Steel Wire Reinforced Foam Core/Composite Skin Sandwich Panel in Abaqus software has been investigated. The rigid projectile is modeled as the three-dimensional shell part. The steel reinforcements are modeled as wire part. The glass-epoxy part is modeled as a three-dimensional ...

ادامه نوشته »

Simulation low energy impact of a rigid hammer on the wood-cement-concrete panel in Abaqus

In this tutorial, Simulation low energy impact of a rigid hammer on the wood-cement-concrete panel in Abaqus has been investigated. The panel contians three layers, top layer is wood-cement part as a soild model, the second layer is normal strenght concrete as a solid part, and third layer is wood-cement ...

ادامه نوشته »

Simulation rocket impact and explosion over a concrete panel in Abaqus

In this tutorial the Simulation rocket impact and explosion over a concrete panel in Abaqus has been investigated. The concrete panel is modeled as a three-dimensional solid part. The rocket is modeled as a three-dimensional shell part, and the TNT is modeeld as a solid part. You can see a ...

ادامه نوشته »

شبیه سازی برخورد و انفجار راکت به روش اس پی اچ و بررسی آسیب بتن در آباکوس

در این ویدئوی آموزشی به شبیه سازی برخورد و انفجار راکت به روش اس پی اچ و بررسی آسیب بتن در نرم افزار آباکوس پرداخته ایم. مدلسازی شامل هندسه بتن به صورت سالید و سه بعدی، هندسه راکت به صورت شل و سه بعدی و در نهایت پارت ماده منفجره ...

ادامه نوشته »

Simulation air blast load over a composite panel(Aluminum+bamboo fiber) in Abaqus

In this tutorial, the Simulation air blast load over a composite panel(Aluminum+bamboo fiber) in Abaqus has been investigated. Because of the symmetry circumstance, one quarter of the geometries are modeled. The aluminum plates are modeled as three-dimensional solid part. The bamboo plate as a core of the composite panel is ...

ادامه نوشته »

Simulation four point bending test of a foamed concrete beam reinforced with steel bars and bamboo fiber in Abaqus

In this tutorial, the Simulation four point bending test of a foamed concrete beam reinforced with steel bars and bamboo fiber in Abaqus has been investigated. The foamed concrete part is modeled as a three-dimensional solid part. The bamboo composite is modeled as a three-dimensional shell part with some layers. ...

ادامه نوشته »
تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
enemad-logo