تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
خانه / بایگانی برچسب: abaqus damage analysis

بایگانی برچسب: abaqus damage analysis

Simulation under water explosion shock over a cylindrical aluminum shell in interaction with soil in Abaqus

In this tutorial, the Simulation under water explosion shock over a cylindrical aluminum shell in interaction with soil in Abaqus has been studied. The water is modeled as a three-dimensional solid part with acoustic behaviour. The aluminum part is modeled as a three-dimensional shell part, and the soil as a ...

ادامه نوشته »

Simulation concrete beam-column joint under cyclic loading in Abaqus-Damage analysis

In this tutorial, the Simulation concrete beam-column joints under cyclic loading in Abaqus-Damage analysis- has been investigated. The concrete beam-column joint is modeled as a three-dimensional solid part. The strips and bars are modeled as three-dimensional wire parts. You can see figures of the assembled parts below The steel material ...

ادامه نوشته »

Simulation shear failure of two steel plates with bolt connection in Abaqus

In this tutorial, the Simulation shear failure of two steel plates with bolt connection in Abaqus has been investigated. The steel plates are modeled as a three-dimensional solid part The bolts with different sizes are modeled as a three-dimensional solid part. You can see a figure of the assembled part ...

ادامه نوشته »

Simulation flexural behavior of the steel beam reinforced with CFRP in Abaqus

In this tutorial, the Simulation flexural behavior of the steel beam reinforced with CFRP in Abaqus has been investigated. The steel beam and CFRP sheet are modeled as three-dimensional shell parts. The rigid bodies are modeled as a discrete rigid body. You can see a figure of the assembled parts ...

ادامه نوشته »

Simulation five points bending of the concrete beam in Abaqus

In this tutorial, Simulation five points bending of the concrete beam in Abaqus has been investigated. The concrete beam is modeled as a three-dimensional solid part. The rebar inside the concrete beam is modeled as a three-dimensional wire part. The rigid shell body is used to model the boundary zone ...

ادامه نوشته »

Simulation profiled steel deck composite slab system under four point bending in Abaqus

In this tutorial simulation profiled steel deck composite slab system under four point bending in Abaqus has been studied. Composite slabs comprised of cold-formed profiled steel sheet and structural concrete topping are commonly used nowadays for the construction of buildings. In this system, steel deck serves as a permanent form ...

ادامه نوشته »

Simulation granite stone cutting by using a rigid cutter in Abaqus

In this tutorial simulation granite stone cutting by using a rigid cutter in Abaqus has been investigated.The granite stone is modeled as three dimensional part ,the cutter and supporter are modeled as rigid body.The Abaqus CAE contains some material model for brittle materials,but they are suitable to simulate the large ...

ادامه نوشته »

Simulation steel beam damage under cyclic loading in Abaqus standard

In this tutorial Simulation steel beam damage under cyclic loading in Abaqus standard has been investigated.Under cyclic loading conditions such as those introduced by earthquake  ground motions, the local buckling is initiated in the compression flange.  However, it disappears and reappears in subsequent cycles. The beam is modeled as three ...

ادامه نوشته »

ٍSimulation of p-section concrete beams under contact explosion(CEL) conditions in Abaqus

In this tutorial Simulation of p-section concrete beams under contact explosion(CEL) conditions in Abaqus has been studied. Reinforced concrete bridges are the most common type of bridges and have a simple structure, low cost and long durability. Among these bridges, reinforced concrete bridges composed of p-section bridge components are among the ...

ادامه نوشته »

Simulation SPH explosion over masonry wall (micro model) in Abaqus and damage investigation

In this tutorial Simulation SPH explosion over masonry wall (micro model) in Abaqus and damage investigation has been studied.The wall is modeled with concrete bricks and concrete beam as three dimensional parts.The TNT part is modeled as sphere solid part. You can see a figure of this simulation at below To ...

ادامه نوشته »
تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
enemad-logo