تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.

آخرین نوشته ها

Simulation compression test of the concrete column with and without steel reinforcement-Compression test

In this tutorial, the Simulation compression test of the concrete column with and without steel reinforcement-Compression test- has been investigated. The concrete column is modeled as a three-dimensional solid part. The steel reinforcements are modeled as wire parts and two rigid bodies as boundary zone and hydraulic jack. You can ...

ادامه نوشته »

شبیه سازی تست فشار ستون کوتاه بتنی با و بدون تقویت کننده فلزی در آباکوس-مقایسه باربری

در این ویدئوی آموزشی به شبیه سازی تست فشار ستون کوتاه بتنی با و بدون تقویت کننده فلزی در آباکوس-مقایسه باربری- پرادخته ایم. مدلسازی به صورت سه بعدی شامل هندسه ستون بتنی، میلگرد ها و اجسام صلب در نقش تکیه گاه و جسم وارد کننده نیرو می باشد. ستون بتنی ...

ادامه نوشته »

Simulation RC column retrofitted with CFRP and epoxy under compression load in Abaqus

In this tutorial, the Simulation RC column retrofitted with CFRP and epoxy under compression load in Abaqus has been done. The circular concrete column is modeled as a three-dimensional solid part. The sell strips and bars are modeled as three-dimensional wire parts. The CFRP is modeled as a conventional shell ...

ادامه نوشته »

Thermal and Structural Analysis of Exhaust Manifold in Abaqus

In this tutorial, the Thermal and Structural Analysis of Exhaust Manifold in Abaqus has been investigated. The manifold geometry is a complex one, so the geometry is imported to the Abaqus from SolidWorks software. You can see a figure of the manifold part below The exhaust manifold is a very ...

ادامه نوشته »

Damage and failure investigation of the CFRP composite military helmet under close blast explosion

In this tutorial, the damage and failure investigation of the CFRP composite military helmet under close blast explosion has been studied. The military helmet is a 3D shell part with eight different layers. The helmet part is imported to the Abaqus because of the part complexity. You can see a ...

ادامه نوشته »

Seismic behavior of RC exterior wide beam-column joints in Abaqus

In this tutorial, the Seismic behavior of RC exterior wide beam-column joints in Abaqus has been simulated. The concrete beam and column are modeled as three-dimensional solid parts. The steel bars and strips are modeled as three-dimensional wire parts. You can see a figure of the assembled parts below Reinforced ...

ادامه نوشته »

High-velocity impact on the RC panel- Paper validation

In this tutorial, the High-velocity impact of a bullet on the RC panel- Paper validation- is investigated. The dimensions are extracted from the paper. The concrete slab is modeled as a three-dimensional solid part. The steel reinforcements are modeled as three-dimensional wire parts. The bullet is modeled as a discrete ...

ادامه نوشته »

Abaqus Full Course of Steel Structure Modeling and Simulation- More than Eight hours Duration

In this course, you will learn all aspects of steel structure modeling and simulation in Abaqus. The lecture contains sixteen sections, in each section, the tutor has explained all thing from A to Z. Geomert modeling, material definition and equations, steps, interaction, load, mesh, and results. The dynamic bolt failure, ...

ادامه نوشته »

Abaqus Full Lecture of Soil modeling, pile group and piled raft, consolidation, bearing capacity, …more than ten hours simulation

In this full lecture, all aspects of soil modeling and simulation are represented. The lecture contains twenty titles about soil, saturated soil, TBM, earthquake, tunnel, embankment construction, geocell reinforced soil, geosynthetic-reinforced soil retaining wall, earthquake over a concrete tunnel, embankment, and excavation, soil consolidation in interaction with the concrete pile, ...

ادامه نوشته »

Abaqus full lecture-High and Low-Velocity Impact- More than ten hours of modeling and simulation

In this lecture, the High and Low-velocity impact phenomenon is investigated. The lecture duration is more than ten hours and during that, twenty different models are simulated based on the research paper as a reference for the material. We define the proper material model for each part for instance in ...

ادامه نوشته »
تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
enemad-logo