تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
خانه / 2020 / مارس

بایگانی ماهانه: مارس 2020

Simulation dynamic tensile test of an aluminum piece by using ductile,shear, and MSFLD damage criterion in Abaqus

In this tutorial, the Simulation dynamic tensile test of an aluminum piece by using ductile, shear, and MSFLD damage criterion in Abaqus has been studied. The aluminum part is modeled as a three-dimensional solid part. You can see a figure of the assembled below The aluminum alloys may fail due ...

ادامه نوشته »

شبیه سازی تست کشش دینامیکی قطعه آلومینیوم با استفاده از معیار های آسیب در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی تست کشش دینامیکی قطعه آلومینیوم با استفاده از معیار های آسیب در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و از یک پارت سالید آلمینیومی به منظور بررسی جدایش و شکست دینامیکی قطعه تحت اثر کشش استفاده شده است. ...

ادامه نوشته »

Simulation dynamic pullout of a steel plate from the RC beam in Abaqus

In this tutorial, the Simulation dynamic pullout of a steel plate from the RC beam in Abaqus has been investigated. The steel plate is modeled as a three-dimensional solid part. The concrete beam is modeled as a three-dimensional solid part. The bars and strips are modeled as three-dimensional wire parts. ...

ادامه نوشته »

شبیه سازی بیرون کشیدن ورق فولادی از تیر بتنی تقویت شده با میلگرد در آباکوس-بررسی آسیب

در این ویدئوی آموزشی به شبیه سازی بیرون کشیدن ورق فولادی از تیر بتنی تقویت شده با میلگرد در نرم افزار آباکوس-بررسی آسیب- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و ورق فولادی به صورت یک مدل سالید و سه بعدی، تیر بتنی به صورت سالید و سه بعدی ...

ادامه نوشته »

Abaqus Welding Package- Simulation various welding process in Abaqus

In this package, you can find ten tutorials about the welding process in Abaqus like friction stir welding, pipe welding, plate welding,…You can find each tutorial separately on the website. This package contains the below list Simulation thermal stress analysis of arc welding between two pipes by using DFLUX subroutine ...

ادامه نوشته »

پکیچ شبیه سازی جوش ذوبی و مقاومتی به روش های مختلف در نرم افزار آباکوس

در این پکیج آموزشی که شامل سیزده آموزش قدم به قدم می باشد، سعی گردیده شده تا روش ها و اشکال مختلف جوش به صورت کامل بیان شود. تک تک مثالها به صورت جداگانه در سایت موجود می باشند و می توانید در صورت نیاز،به تهیه آنها اقدام نمائید.توضیحات هر ...

ادامه نوشته »

Simulation CEL explosion over the composite panel(Concrete-Steel bar-Steel sheet) in Abaqus

In this tutorial, the Simulation CEL explosion over the composite panel(Concrete-Steel bar-Steel sheet) in Abaqus has been done. The concrete is modeled as three dimensional solid part. The TNT and steel sheet are modeled as a three-dimensional solid part. The steel bars are modeled as three-dimensional wire part. The Eulerian ...

ادامه نوشته »

شبیه سازی انفجار به روش کوپل اویلری لاگرانژی روی یک پنل مرکب(بتن-میلگرد-ورق فولادی) در آباکوس

در این ویدئوی آموزشی به شبیه سازی انفجار به روش کوپل اویلری لاگرانژی روی یک پنل مرکب(بتن-میلگرد-ورق فولادی) در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و شامل پارت هدف بتنی به صورت سه بعدی و سالید، پارت ورق فولادی به صورت سه بعدی و سالید ...

ادامه نوشته »

Simulation of Stud Connected Steel-UHPC Composite Girders Subjected to four-point bending in Abaqus

In this tutorial, Simulation of Stud Connected Steel-Concrete Composite Girders Subjected to four-point bending in Abaqus has been studied. The performance of steel-concrete composite (SCC) girders for static and dynamic loads depends significantly on the force transfer mechanism at the interface between steel beam and concrete. Stud connected SCC girders consist ...

ادامه نوشته »

شبیه سازی خمش چهار نقطه ای تیر فولادی-بتن فوق توانمند به همراه گل میخ در نرم افزار آباکوس

در این ویدئوی آموزشی به شبیه سازی خمش چهار نقطه ای تیر فولادی-بتن فوق توانمند به همراه گل میخ در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی می باشد و پارت تیر فولادی به همراه گل میخ ها به صورت سه بعدی و سالید ترسیم شده اند. ...

ادامه نوشته »

Simulation dynamic bolt failure (bolt and steel plates joint) in Abaqus

In this tutorial, the Simulation dynamic bolt failure (bolt and steel plates joint) in Abaqus has been studied. The upper and bottom steel plates are modeled as three-dimensional solid parts. The bolts are modeled as three-dimensional solid parts. You can see a figure of the assembled parts below. Two main ...

ادامه نوشته »

شبیه سازی پارگی اتصال پیچی دو ورق تحت کشش در نرم افزار آباکوس- تحلیل دینامیکی

در این ویدئوی آموزشی به شبیه سازی پارگی اتصال پیچی دو ورق تحت کشش در نرم افزار آباکوس- تحلیل دینامیکی- پرداخته ایم. مدلسازی به صورت سه بعدی بوده که شامل دو پارت ورق فولادی رویی و زیرین می باشد که به صورت سالید و تغییر شکلپذیر ترسیم شده اند. پیچ ...

ادامه نوشته »

Simulation dynamic failure behavior of steel beam-to-column bolted connections in Abaqus

In this tutorial, the Simulation dynamic failure behavior of steel beam-to-column bolted connections in Abaqus has been investigated. Stainless steel displays numerous desirable properties which motivated many researchers to investigate its use in structural applications. Despite having comparatively high initial cost, its excellent corrosion resistance; outstanding durability; superior response to ...

ادامه نوشته »

شبیه سازی اتصال تیر به ستون فولادی با نبشی و پیچ تحت بار دینامیکی در آباکوس- بررسی آسیب

در این ویدئوی آموزشی به شبیه سازی اتصال تیر به ستون فولادی با نبشی و پیچ تحت بار دینامیکی در آباکوس- بررسی آسیب- پرداخته ایم. مدلسازی به صورت سه بعدی می باشد. پارت ستون و تیر فولادی به صورت سه بعدی و سالید ترسیم شده اند. پارت نبشی و پیچ ...

ادامه نوشته »

Simulation cold spray process of steel particle on the Inconel surface by using ALE method in Abaqus

In this tutorial, the Simulation cold spray process of steel particle on the Inconel surface by using the ALE method in Abaqus has been studied. The steel particle is modeled as a three-dimensional solid part. The Nickel-Chromium(Inconel) part is modeled as a three dimensional solid part. You can see a ...

ادامه نوشته »

شبیه سازی پاشش سرد ذرات فولاد به سطح آلیاژ نیکل-کروم در نرم افزار آباکوس-مقیاس میکرو

در این ویدئوی آموزشی به شبیه سازی پاشش سرد ذرات فولاد به سطح آلیاژ نیکل-کروم در نرم افزار آباکوس-مقیاس میکرو- پرداخته ایم. مدلسازی به صورت سه بعدی بوده و ذره فولادی به صورت یک کره سه بعدی و سالید با شعاع چهل میکرو متر طراحی شده است. پارت هدف یا ...

ادامه نوشته »
تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
enemad-logo