تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
خانه / 2019 / مارس

بایگانی ماهانه: مارس 2019

Simulation bearing capacity of a three dimensional square foundation in Abaqus

In this tutorial Simulation bearing capacity of a three dimensional square foundation in Abaqus base on the Sam Helwany’s book has been investigated. To model soil and foundation a one three dimensional part is used.You can see a figure about it at below The elastic and cap plasticity with cap ...

ادامه نوشته »

شبیه سازی و محاسبه ظرفیت باربری یک پی مربعی سه بعدی در نرم افزار آباکوس

در این ویدئو به شبیه سازی و محاسبه ظرفیت باربری یک پی مربعی سه بعدی در نرم افزار آباکوس به صورت قدم به قدم پرداخته ایم. مدلسازی بر اساس مثالی از کتاب Sam Helwany بوده که در آن به دلیل تقارن فقط یک چهارم مدل ایجاد شده است. مدلسازی به ...

ادامه نوشته »

Simulation on shock response of marine sandwich structures subjected to UNDEX loading in Abaqus

In this tutorial Simulation on shock response of marine sandwich structures subjected to UNDEX loading in Abaqus has been investigated.In modern sea combat, in which strike power has increased markedly, the structures of naval ships must be designed to with-stand shock loads resulting from weapon hits.To improve the design of ...

ادامه نوشته »

شبیه سازی انفجار زیر آب در فاصله نزدیک روی یک سازه ساندویچی فولادی در نرم افزار آباکوس

در این ویدئو به شبیه سازی مرحله به مرحله انفجار زیر آب در فاصله نزدیک روی یک سازه ساندویچی فولادی در نرم افزار آباکوس به روش UNDEX پرداخته ایم. مدلسازی به صورت سه بعدی بوده و هندسه پنل ساندویچی از دو ورق رویی و زیرین به همراه هندسه مشبک ذاخلی ...

ادامه نوشته »

Simulation end bearing capacity of a pile under rapid load in Abaqus

In this tutorial simulation end bearing capacity of a pile under rapid load in Abaqus base in the Sam Helwany book has been investigated. To model pile  and soil asymmetric shell parts has been used.In geotechnical engineering, bearing capacity is the capacity of soil to support the loads applied to ...

ادامه نوشته »

شبیه سازی و محاسبه ظرفیت باربری یک شمع استوانه ای بتنی در آباکوس

در این ویدئو به شبیه سازی و محاسبه قدم به قدم ظرفیت باربری یک شمع استوانه ای بتنی در نرم افزار آباکوس پرداخته ایم.شبیه سازی به صورت تقارن محوری بوده، پارت خاک  و شمع به صورت شل مدل شده اند. در شکل زیر می توانید شماتیک مسئله را مشاهده کنید. ...

ادامه نوشته »

Simulation Bearing Capacity Failure of a Strip Foundation in Abaqus

In this tutorial Simulation Bearing Capacity Failure of a Strip Foundation in Abaqus base on the Sam Helwany’s book has been studied. Because of the symmetric condition, two dimensional shell part is used for both soil and foundation. You can see a figure of schematic at below Elastic material for ...

ادامه نوشته »

شبیه سازی پی نواری و محاسبه ظرفیت باربری آن در نرم افزار آباکوس به صورت دو بعدی

در این ویدئو به شبیه سازی مرحله به مرحله پی نواری و محاسبه ظرفیت باربری آن در نرم افزار آباکوس به صورت دو بعدی پرداخته ایم. هندسه شامل دو پارت خاک و بتن بوده که هر دو به صورت شل دو بعدی ترسیم شده اند. در این آنالیز نحوه شبیه ...

ادامه نوشته »

Numerical simulation of Electro-Hydraulic forming process by using acoustic method in Abaqus

In this tutorial Numerical simulation of Electro-Hydraulic forming process by using acoustic method in Abaqus has been verified base on the ISI paper. Electro-hydraulic forming is one of the methods that highly considered among automotive  specialists. This method is known as “high strain rate forming” method. In this process, an ...

ادامه نوشته »

شبیه سازی آکوستیکی فرآیند الکتروهیدرولیک فرمینگ در نرم افزار آباکوس-صحت سنجی

در این ویدئو به صحت سنجی مقاله و شبیه سازی آکوستیکی فرآیند الکتروهیدرولیک فرمینگ در نرم افزار آباکوس به صورت قدم به قدم پرداخته ایم. شکلدهی الکتروهیدرولیک نوعی از شکلدهی است که به وسیله اعمال ولتاژ الکتریکی بالایی به سیال، باعث ایجاد موج فشاری شدیدی در آن شده که این ...

ادامه نوشته »

ٍSimulation of hollow steel piles subjected to buried blast loading(CEL explosion) in Abaqus

In this tutorial Simulation of hollow steel piles subjected to buried blast loading(CEL explosion) in Abaqus has done.A pile is a load bearing component of a structure that transfers the structural load to the hard soil or rock underground. The modern human civilization and smart infrastructure depend largely on the ...

ادامه نوشته »

شبیه سازی انفجار به روش کوپل اویلری لاگرانژی در عمق خاک روی شمع فلزی در نرم افزار آباکوس

در این ویدئو به شبیه سازی قدم به قدم انفجار به روش کوپل اویلری لاگرانژی در عمق خاک روی شمع فلزی در نرم افزار آباکوس پرداخته ایم.شبیه سازی به صورت سه بعدی بوده و شمع های فلزی به صورت لوله و با المان سالید،خاک و ماده منفجره به صورت اویلری ...

ادامه نوشته »

Simulation granite stone cutting by using a rigid cutter in Abaqus

In this tutorial simulation granite stone cutting by using a rigid cutter in Abaqus has been investigated.The granite stone is modeled as three dimensional part ,the cutter and supporter are modeled as rigid body.The Abaqus CAE contains some material model for brittle materials,but they are suitable to simulate the large ...

ادامه نوشته »

شبیه سازی برش سنگ با استفاده از یک کاتر صلب در نرم افزار آباکوس

در این ویدئو به شبیه سازی مرحله به مرحله برش سنگ با استفاده از یک کاتر صلب در نرم افزار آباکوس پرداخته ایم. کاتر به صورت جسم سه بعدی صلب و سنگ نیز به صورت پارت تغییر شکلپذیر سه بعدی بوده که در زیر آن یک صفحه صلب به عنوان ...

ادامه نوشته »

Simulation CFRP jacketed reinforced concrete beam-column joints in Abaqus

In this tutorial simulation CFRP jacketed reinforced concrete beam-column joints in Abaqus has been investigated.Various types of strengthening materials such as steel plates, ferrocement, and fiber reinforced polymers are available in the construction industry to be used for jacketing of the affected components, the most common being steel jackets.These types ...

ادامه نوشته »

شبیه سازی اتصال تیر به ستون بتنی تقویت شده با میلگرد و CFRP در نرم افزار آباکوس

در این ویدئو به شبیه سازی مرحله به مرحله اتصال تیر به ستون بتنی تقویت شده با میلگرد و CFRP در نرم افزار آباکوس پرداخته ایم. تیر و ستون بتنی به صورت سه بعدی و تغییر شکلپذیر با متریال مدل CDP، میلگردها به صورت پارت وایر و با متریال استیل ...

ادامه نوشته »

Simulation concrete piled raft in interaction with soil in Abaqus

In this tutorial Simulation concrete piled raft in interaction with soil in Abaqus has been done.The piled raft foundation system has recently been widely used for many structures, especially high rise buildings. In this foundation, the piles play an important role in settlement and differential settlement reduction, and thus can ...

ادامه نوشته »

شبیه سازی دسته شمع در خاک به صورت سه بعدی تحت بار فشاری در نرم افزار آباکوس

در این ویدئو به شبیه سازی مرحله به مرحله دسته شمع در خاک به صورت سه بعدی تحت بار فشاری در نرم افزار آباکوس پرداخته ایم. در این مثال از پنج شمع با مقطع دایره ای متصل به دسته یا Raft در خاک استفاده شده است.تمامی پارت ها به صورت ...

ادامه نوشته »

Finite Element simulation of Electro-Hydraulic Forming of Sheet by using time pressure curve in Abaqus

In this simulation Finite Element simulation of Electro-Hydraulic Forming of Sheet by using time pressure curve in Abaqus has been investigated. Sheet metal forming processes are those in which force is applied to a piece of sheet metal to modify its geometry  rather than remove any material. The applied force ...

ادامه نوشته »

شبیه سازی فرآیند الکتروهیدرولیک با استفاده از مدل فشار زمان در آباکوس-صحت سنجی مقاله

در  این ویدئو به صحت سنجی و شبیه سازی قدم به قدم فرآیند الکتروهیدرولیک با استفاده از مدل فشار زمان در نرم افزار آباکوس پرداخته ایم. مقاله مورد استفاده در این شبیه سازی در سال ۲۰۱۴ در یکی از ژورنال های الزویر چاپ شده است.شکل‌دهی الکتروهیدرولیکی یک فرایند شکل‌دهی ورق ...

ادامه نوشته »

Simulation concrete slab cutting by using a rigid cutter in Abaqus

In this tutorial Simulation concrete slab cutting by using a rigid cutter in Abaqus has been investigated.Concrete cutting is a process of controlled sawing, drilling and removal of concrete performed by skilled operators using special saws that use diamond impregnated blades. Unlike the old-fashioned dusty jack hammer method, modern concrete ...

ادامه نوشته »

شبیه سازی برش قطعه بتنی با استفاده از یک کاتر صلب در نرم افزار آباکوس

در این ویدئو به شبیه سازی قدم به قدم برش یک قطعه بتنی با استفاده از یک کاتر صلب در نرم افزار آباکوس پرداخته ایم. برای برش بتن روش های مختلفی وجود داره که از جمله آنها می توان به برش با کاتر،برش با عمود بر و برش با سیم ...

ادامه نوشته »

Simulation concrete beam-column joints in Abaqus and damage investigation

In this tutorial simulation concrete beam-column joints in Abaqus has been studied. Strengthening of existing reinforced concrete structures is now a major part of the construction activity all over the world. The RCC structures constructed across the world are often found to exhibit distress and suffer damage, even before service ...

ادامه نوشته »

شبیه سازی اتصال تیر به ستون بتنی تقویت شده با میلگرد تحت بار عمودی در نرم افزار آباکوس

در این ویدئو به شبیه سازی اتصال تیر به ستون بتنی تقویت شده با میلگرد تحت بار عمودی در نرم افزار آباکوس پرداخته ایم. استفاده از سازه های بتنی در بسیاری از نقاط دنیا امری شایع می باشد که مقاوم سازی آنها تحت بارهای مختلف از اهمیت خاصی برخوردار است. ...

ادامه نوشته »

Simulation steel beam damage under cyclic loading in Abaqus standard

In this tutorial Simulation steel beam damage under cyclic loading in Abaqus standard has been investigated.Under cyclic loading conditions such as those introduced by earthquake  ground motions, the local buckling is initiated in the compression flange.  However, it disappears and reappears in subsequent cycles. The beam is modeled as three ...

ادامه نوشته »

شبیه سازی بارگذاری تکراری روی یک تیر به صورت استاتیکی و بررسی آسیب بوجود آمده در نرم افزار آباکوس

در این ویدئو به شبیه سازی قدم به قدم بارگذاری تکراری روی یک تیر به صورت استاتیکی و بررسی آسیب بوجود آمده در آن در نرم افزار آباکوس پرداخته ایم. مدلسازی به صورت سه بعدی بوده و برای تیر از المان شل استفاده شده است. متریال مورد استفاده برای تیر ...

ادامه نوشته »

Simulation earthquake over a concrete tunnel in interaction with soil in Abaqus

In this tutorial Simulation earthquake over a concrete tunnel in interaction with soil in Abaqus has been investigated. The tunnel industry has considered that tunnels, especially tunnels in rock, are naturally resistant to earthquake action, including faulting, shaking, deflection and ground failure. As the number of case histories of tunnels ...

ادامه نوشته »

Simulation milling cutting process in Abaqus

In this tutorial simulation milling process in Abaqus has been investigated.Milling is a cutting process that uses a milling cutter to remove material from the surface of a workpiece. The milling cutter is a rotary cutting tool , often with multiple cutting points. As opposed to drilling, where the tool is ...

ادامه نوشته »

شبیه سازی فرآیند بغل تراشی فولاد با مته و میله فرز انگشتی در نرم افزار آباکوس

در این ویدئو به شبیه سازی قدم به قدم فرآیند بغل تراشی فولاد با مته و میله فرز انگشتی در نرم افزار آباکوس پرداخته ایم. در این مثال از دو ابزار مته و میله فرز انگشتی در دو شبیه سازی جداگانه استفاده شده است. در مثال اول برای براده برداری ...

ادامه نوشته »

Simulation honey comb steel beam under cyclic load to extract hysteresis diagram in Abaqus

In this tutorial Simulation honey comb steel beam under cyclic load to extract hysteresis diagram in Abaqushas been studied.Honey Comb Castellated Beam has a deeper part than Comparable Solid Beam, which has greater resistance to deflection. Therefore, the product is most often used in Long Span applications with light and ...

ادامه نوشته »

شبیه سازی بارگذاری تکراری روی یک تیر لانه زنبوری و تحلیل هیسترزیس آن در نرم افزار آباکوس

در این ویدئو به شبیه سازی قدم به قدم بارگذاری تکراری روی یک تیر لانه زنبوری و تحلیل هیسترزیس آن در نرم افزار آباکوس پرداخته ایم. هیسترزیس یا پسماند پدیده‌ای است که وابستگی حالت فعلی یک سیستم به مسیر تغییرات آن را نمایش می‌دهد.اکثر سازه ها در زمین لرزه های ...

ادامه نوشته »
تمامی مطالب این سایت محفوظ بوده و هر گونه کپی برداری از مطالب این سایت پیگرد قانونی دارد.
enemad-logo